Independent appliance repair
What changed? Start with the symptom.
A noise, a leak, a cycle that stops partway. Pick your appliance and follow what you observed.

Start from what you notice.
Kenmore washer not spinning
Start with what the display and the lid or door say.
Kenmore washer shaking
Violent shaking on a Kenmore washer comes down to a lopsided load, feet that are not all touching, shipping bolts left in, or a floor that flexes.
Kenmore washer controls not responding
On a 796 front-load washer, buttons that do nothing often mean the Control Lock is on and CL is flashing in the display.
Kenmore washer leaking
Work out where the water appears first.
Kenmore washer drum not turning
None of the Kenmore guides we read describe belts or pulleys, so we cannot name a cause from them.
Kenmore washer won't start
A Kenmore washer that will not start or agitate is usually missing power, a closed and locked lid or door, a pressed START, or water.
Kenmore washer not draining
When water stays in a Kenmore washer, the guides start with the drain hose, then the drain pump filter, then the height of the drain.
Kenmore washer noisy
Several loud sounds are normal on a Kenmore washer: clicking from the door lock, humming from the drain pump, spraying, splashing and a high whine at top spin.
Kenmore dryer takes too long
Long drying on a Kenmore dryer usually traces back to airflow: a clogged lint screen, a crushed or lint-packed exhaust vent, or a vent run that is too long.
Kenmore dryer temperature problems
A Kenmore dryer that runs too hot, too cool or without heat is covered by three kinds of check in the guides: airflow, the household power supply, and a sensor message.
Kenmore dryer burning smell
The Kenmore guides name only a few harmless odor sources: a new electric heating element on first use, and fumes from paint or varnish in the room.
Kenmore dryer drum not turning
The Kenmore dryer guides do not describe a mechanical cause for a drum that will not turn, so we stay with what they print: a dryer that will not run needs power, a firmly closed door and a firm START press.
Kenmore dryer controls not responding
If the buttons on a Kenmore dryer do nothing, look for CL in the display: the Control Lock is on.
Kenmore range controls not responding
On the Kenmore 790 ranges, a dead-looking oven panel usually means one of four things: the oven lockout is on, the clock was never set, an F or E code stopped the control, or power is missing.
Kenmore range oven door problems
A Kenmore oven door that will not open is almost always the self-clean lock, which holds until the oven has cooled.
Kenmore range burner problems
On a Kenmore 790 gas cooktop, a flame that is too high, uneven or orange has a short list of causes in the guide: a knob set high, a burner cap sitting wrong, clogged ports, moisture after cleaning or an incorrect LP conversion.
Kenmore range burner won't ignite
If a Kenmore 790 gas burner will not light, the guide asks you to push the knob in and turn it fully to Lite, clear the ports, and confirm the range has power.
Kenmore range self-clean problems
If self-clean will not start or leaves dirt on a Kenmore 790 oven, the guide points to settings and prep: an active oven lockout, racks left in, a door not fully closed, spills not wiped, or a cooling fan that is not moving air.
Kenmore range gas smell
Gas odor near a Kenmore range means no flames, no switches.
Kenmore range temperature problems
If a Kenmore 790 oven runs hot, runs cool or bakes unevenly, the guides first look at technique: preheat, rack position and pan spacing.
Kenmore refrigerator frost buildup
Frost in a Kenmore 795 refrigerator mostly comes from moist air getting in: doors opened often, doors that do not close fully, humid weather or unwrapped food.
Kenmore refrigerator temperature problems
For a Kenmore 795 refrigerator that is too warm, too cold or uneven, the guide lists install time, blocked vents, door openings, hot food, room temperature and the control setting.
Kenmore refrigerator light not working
The Kenmore 795 guide says the refrigerator lamp is LED lighting and that a failed LED needs a qualified technician.
Kenmore refrigerator leaking
The Kenmore 795 guide has no leak-troubleshooting row, so the sources are thin.
Kenmore refrigerator not cooling
If a Kenmore 795 refrigerator is not cooling, the guide's first checks are that the control is not OFF, that Demo Mode is off, and that you have waited through a defrost or a recent install.
Kenmore refrigerator door seal problems
For a Kenmore 795 door that will not close, pops open or sticks, the guide lists blocking food, misplaced bins, doors put back wrongly, an unlevel cabinet and dirty gaskets.
Kenmore refrigerator noisy
The Kenmore 795 guide lists a long run of normal refrigerator sounds: clicking, rattling, whooshing, gurgling, popping, sizzling, dripping and a pulsating hum.
Kenmore dishwasher controls not responding
On the Kenmore 665 Ultra Wash dishwasher, buttons that do nothing usually mean Control Lock is on.
Kenmore dishwasher won't start
A Kenmore 665 dishwasher that will not run needs a closed and latched door, Control Lock off, a selected cycle and power.
Kenmore dishwasher detergent dispenser
Soap still in the cup, or a tablet lying on the tub floor, sends the Kenmore 665 guide to three questions: is anything blocking the lid, is the detergent fresh and free of lumps, and did the cycle really finish?
Kenmore dishwasher leaking
The Kenmore 665 guide gives two causes for leaks: an installation that is not level, and suds from too much detergent or the wrong kind.
Kenmore freezer does not run
When a Kenmore freezer does not run, the guide lists five causes: a GFCI-protected circuit, the temperature control in OFF, a loose plug, a blown fuse, a breaker that has tripped, and a power outage.
Kenmore freezer too warm, too cold or running constantly
For a freezer that is too warm, the guide points to the control set too warm, a lid opened often, a lid not seating, a large warm load, or a recent disconnect.
Kenmore ice maker not making ice
For a Kenmore bottom-freezer ice maker that makes nothing, the guide lists a fresh install, the power switch, a dirty ice sensor, no water supply, a blocked shut-off arm or sensor, and reverse osmosis pressure.
Kenmore ice has a bad taste, odor or looks cloudy
Kenmore names six reasons for ice with a bad taste or odor: minerals such as sulfur in the water, a new ice maker, old ice, poorly wrapped food, a dirty refrigerator and a dirty ice bin.
Kenmore wall oven does not operate
With a completely dead oven, Kenmore's guide starts with power: a secure cord, a breaker or fuse that has failed, an outage, and the controls.
Kenmore wall oven self-clean cycle not working
If the self-clean cycle does not work, Kenmore lists three causes: the door is open, the controls are not set properly, or the cycle was interrupted.
Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame.
Kenmore radiant cooktop element not heating
For a Kenmore radiant cooktop, the guide names a blown fuse or breaker trip, an outage, a heat setting too low, the wrong control for the element, incorrect voltage, and lightweight or warped pans.
One code, more than one meaning
Find the model number.
Then read the code.
A Kenmore code can mean one thing on a dryer from one family and another on a dryer from the next. Match the digits before the dot, then look it up.
Kenmore codes by modelOn a 796 front-load Kenmore washer, LE means a motor error; on the 796 top-load (2927) it means the motor's thermal overload protection has tripped. Both guides give the same first move: let the washer stand for 30 minutes, then restart the cycle.
Read the LE checks29 researched washer codes. A code can mean different things on different models, so read it against your own manual.
What do I do first when the display stays blank?
Choose your appliance first, then the symptom that best matches what you see. Each page lists the safe checks and says when to stop and book. It does not diagnose the part.
What if two things go wrong at once?
Read both pages and name both problems when you book. Two symptoms can share a cause, so the technician needs the whole picture and not only the louder part.
Will a problem page name the failed part?
No. Each page explains what a symptom usually points to and which checks are safe to try. Only a technician at the appliance can say which part has failed.
When should I stop and call?
Stop for a gas smell, a burning smell, sparking or water near a plug. Cut power at the breaker or close the valve if you can reach it safely, then book a visit.
Code, symptom, part or service
Link the message to what comes next.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.








