Before work starts
After the technician has examined the appliance you are given the cost of the repair, and you decide whether to go ahead.
Independent appliance repair
We repair Kenmore built-in wall ovens, single and double, electric and gas: an oven that stays cold, a display that beeps with an F code, a door that will not lock or unlock, a clock that keeps flashing. Give us the model number and what the display says, then book a technician.


With a completely dead oven, Kenmore's guide starts with power: a secure cord, a breaker or fuse that has failed, an outage, and the controls. On an electric oven the clock must be set after power returns. On a gas oven, open the gas shut-off valve.

If the self-clean cycle does not work, Kenmore lists three causes: the door is open, the controls are not set properly, or the cycle was interrupted. If dirt remains afterward, the frame and door area outside the gasket were not hand cleaned, or the spillover was heavy.
Kenmore's range guides does not print F11. It lists one rule for any F code instead. Clear the display, reprogram, write the number down and arrange a visit if it reappears. Shut off gas if you smell it.
On the 405.7608#, a three-second press of + and - together locks the panel; LOC flashes and then stays lit. That is a panel lock rather than an error, and the oven door stays free.
Control generation and fuel type decide wall oven parts, so we quote none up front. After diagnosis the technician checks the part against your model number and waits for your go-ahead.
What happens after you book.
Model number first.

Type in the number from the label, along with what the appliance does. A photo of the label works too.

The technician reads the code against your model, finds the failed part and gives you a cost before starting.

The new part goes in, the cycle is tested, and you hear what was done.
On the Elite electric wall oven the display flashes after the plug goes in or power returns, and the oven cannot be programmed until the clock is set.
The guides use F11 as their example. Press STOP (STOP/CLEAR on the gas oven) to silence it, reprogram, and record the number if it returns. They print no meanings.
If d=O or -dr- shows, the door was left open with self-clean set. Close the door; on the gas oven also press CANCEL.
A gas wall oven heats its glow bar igniter for under a minute before gas flows. Never try to light it in an outage: turn the knob to OFF and wait for power.
The motor-driven lock on the Elite oven needs about 15 seconds to close after you start a lockout or self-clean. Do not force the door while it moves.
The control can shift the oven up or down by as much as 35 degrees F to match your recipes. That offset leaves the self-clean and broil temperatures unchanged.
An F code returns after you clear it and reprogram the oven.
The oven stays cold with the clock set, the breaker on and, on gas, the supply valve open.
The door stays locked after the oven has cooled, or the lock never closes for self-clean.
The breaker trips again after the oven has run before.
If you smell gas, leave the house first. Wiring and gas fittings are the technician's work.
Arrange a diagnosticAfter the technician has examined the appliance you are given the cost of the repair, and you decide whether to go ahead.
Covered repairs under a Kenmore manufacturer warranty are handled through Kenmore. We stand behind our own work with a workmanship warranty.
Yes. Freestanding and slide-in ranges have their own page. Tell us which you own, and give the model number from the serial plate.
The wall oven guides use it only as an example of an F code and print no meaning. Clear it with STOP, reprogram, and book a technician if it returns.
After a plug-in or a power cut the clock flashes, and the Elite oven cannot be programmed until you set it. If it flashes with power steady, book a visit.
No. The guide says the burner valves will not open without power. Turn the knob to OFF, then back to your setting once the power returns.
If the oven is within the manufacturer's warranty, the manufacturer handles that repair. Otherwise book us and we agree the price before work begins.
Code, symptom, part or service
Kenmore's range guides does not print F11. It lists one rule for any F code instead. Clear the display, reprogram, write the number down and arrange a visit if it reappears. Shut off gas if you smell it.
With a completely dead oven, Kenmore's guide starts with power: a secure cord, a breaker or fuse that has failed, an outage, and the controls. On an electric oven the clock must be set after power returns. On a gas oven, open the gas shut-off valve.
Kenmore’s Elite 790 ranges lock the oven door with a motor-driven latch. The guide says it locks automatically when you turn on oven lockout (“Loc” shows) and for Self Clean, and warns you not to open or close the door while the latch is moving.
Book a diagnostic for your model, carried out at the appliance.
Office details, and the access information to pass along.