Start from the symptom
Kenmore oven wall oven self-clean cycle not working.
If the self-clean cycle does not work, Kenmore lists three causes: the door is open, the controls are not set properly, or the cycle was interrupted. If dirt remains afterward, the frame and door area outside the gasket were not hand cleaned, or the spillover was heavy.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Close the door
A cycle cannot run while the door stands open. If the display shows dr or d=O, the door was open when self-cleaning was set. Close it.
- 2
Set the controls again
Follow the instructions in your guide for setting the cycle. Gas models list a stop time 2 to 4 hours after the start time.
- 3
Recover from an interruption
Follow the steps under Stopping or Interrupting a Self-Cleaning Cycle in your guide.
- 4
Hand clean outside the seal
Before starting, clean the oven frame and door liner outside the gasket with a stiff nylon brush and water or a nylon scrubber. Do not clean the gasket itself.
- 5
Pick a longer cycle
For heavy spillovers, set a longer cleaning time.
- 6
Expect flames or smoke
Flames inside the oven or smoke from the vent after heavy spillovers can be normal at high temperatures. Wipe up excess spillovers first.
More about this symptom.
What does Kenmore list when self-clean does not work?#
The door is not closed, the controls are not set properly, or the cycle was interrupted. Follow your guide's steps to set it again.
How do I get better cleaning results?#
Hand clean the oven frame and liner outside the gasket using a stiff nylon brush and water, and choose a longer cycle for heavy spillovers.
When does a do-it-yourself check become a bad idea?#
If the door is shut, the controls are right and the cycle refuses to start, or an F code returns. Never force a locked door open.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.
If the display adds a code.
Keep the exact message.
We have not researched code meanings for this appliance. Use its model manual, and attach a photo of the display to your request.
See the research statusWhen observation becomes a service request.
Leave internal testing to a technician.
The cycle will not start with the door closed and controls set.
An F code shows during the clean.
Smoke is heavy and does not stop.
The door will not unlock after the cycle.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore wall oven self-clean cycle not working guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite electric wall oven 790.481x
- Use & Care Guide, Kenmore gas built-in wall oven 790.3017, 790.3047
Go by the instructions for your exact model. Check how we research these pages.
Why does my Kenmore oven say dr when I set a clean cycle?
The door was left open and the controls were set for self-cleaning. Close the door. On the gas model, push the Cancel pad as well.
May I scrub the oven door gasket?
No. Kenmore warns that cleaning the gasket damages it. Hand clean the oven frame and the liner outside the gasket before you start a cycle.
Why is there still soil after the cycle?
The areas outside the oven seal are not in the self-cleaning area. Burned-on residue also remains after heavy spillovers. Clean those areas first and set a longer cycle next time.
Is smoke during self-clean normal?
The guide calls flames inside the oven or smoke from the vent normal after excessive spillovers, especially at high temperatures. Wipe up large spills first to reduce it.
What does an F code mean during cleaning?
The electronic control detected an error. Press Stop to clear it and stop the beeping, reprogram the oven, and if it returns, record the number and book a technician.
Code, symptom, part or service
Link the message to what comes next.
Kenmore wall oven does not operate
With a completely dead oven, Kenmore's guide starts with power: a secure cord, a breaker or fuse that has failed, an outage, and the controls. On an electric oven the clock must be set after power returns. On a gas oven, open the gas shut-off valve.
Oven door gasket
On self-cleaning Kenmore ovens, the gasket is a woven seal where the door meets the oven frame. Kenmore’s guides say not to clean, rub, move or pull it out, because the weave is what makes a good seal. Hand-clean the frame and liner around it before you run a self-clean cycle.
Oven repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.
