Start from the symptom
Kenmore refrigerator not cooling.
If a Kenmore 795 refrigerator is not cooling, the guide's first checks are that the control is not OFF, that Demo Mode is off, and that you have waited through a defrost or a recent install. The compressor running longer is often normal.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Control not OFF
On some models the control can be switched to OFF. Turn it on and follow the temperature settings in the guide.
- 2
Demo Mode
Demo Mode keeps the lights working but stops cooling. If the pad says OFF, hold Refrigerator Temp and Ultra Ice for five seconds with a door open.
- 3
Wait out defrost and installs
Wait 30 minutes after a defrost cycle. A recent install or power return can take up to 24 hours. A unit moved on its side must stand upright 24 hours before power.
- 4
Check the doors and heat
Doors that are not shut, a large hot load, or a hot location make the compressor run longer. At 70 F expect it to run about 40 to 80 percent of the time.
- 5
Condenser cover
Vacuum the cover and vents. Do not remove the panel over the coil.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.
Read the related care guide.

Frost in the freezer? Start with the door and the drawer.
Frost in a Kenmore 795 bottom-freezer comes mostly from warm, humid air getting in. The guides name frequent or long door openings, a door that does not close properly, humid weather and unwrapped food. Fix the door, wrap the food, then wait 24 hours.

Power was out? Keep the doors closed and give it a day.
For an outage of 24 hours or less, keep every refrigerator door closed. After that, the Kenmore 795 guides say to move frozen food to a freezer locker. When power returns, allow up to 24 hours for full cooling and check the display for OFF or a door alarm.
When observation becomes a service request.
Leave internal testing to a technician.
Both sections stay warm after 24 hours with the control on, Demo Mode off and vents clear. Book a visit.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore refrigerator not cooling guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite bottom-freezer refrigerator 795.7802/7804/7902/7904
Go by the instructions for your exact model. Check how we research these pages.
Why is my refrigerator running but not cooling?
Check Demo Mode, the control setting, door closure and the condenser cover. The compressor also runs longer in a warm room.
How long should a new Kenmore take to cool?
Up to 24 hours per compartment, according to the guide.
It was moved on its side. Is that a problem?
The guide says to let it stand upright 24 hours before connecting it to power.
Is a constantly running compressor normal?
Modern refrigerators run longer but use less energy, the guide says. At 70 F expect roughly 40 to 80 percent run time.
Code, symptom, part or service
Link the message to what comes next.
Kenmore refrigerator Er CO: what the documents print
Kenmore's 795 refrigerator guides does not print Er CO. It lists symptoms, a door alarm and Demo Mode instead. Close both doors, check for Demo Mode, and arrange a visit if the message remains.
Kenmore refrigerator frost buildup
Frost in a Kenmore 795 refrigerator mostly comes from moist air getting in: doors opened often, doors that do not close fully, humid weather or unwrapped food. The guide treats frost inside sealed packages as normal for wet foods stored too long.
Refrigerator condenser coils
The condenser coils release heat from the sealed system. The Kenmore 795 guide’s care section tells you to vacuum the condenser cover and vents with a brush attachment and says not to remove the panel over the coil area. It gives no cleaning schedule.
Refrigerator repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.
