Start from the symptom
Kenmore washer won't start.
A Kenmore washer that will not start or agitate is usually missing power, a closed and locked lid or door, a pressed START, or water. Check the plug and breaker, close the lid or door and press START, then confirm the faucets are open.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Plug and breaker
The guides want a grounded 3-prong, 120-volt outlet. Reset the breaker or replace the fuse, never increase fuse capacity, and avoid extension cords.
- 2
Lid or door, then START
If you opened the lid mid-cycle on a Calypso, closing it is not enough; press START. On the 110 front-load, a cycle must be selected and START held for one second.
- 3
Water supply
A Calypso that will not fill or wash is tied to faucets that are off, kinked inlet hoses or clogged valve screens. On the 110 front-load, F20 means no or too little water.
- 4
Delay Time and display codes
On a Calypso, check that Set Delay Time is off. PF means a power interruption; any cycle you pick clears it on the 796 front-load.
- 5
Door recently left open
The 110 front-load guide asks whether the door stayed open after the last cycle and whether it is firmly shut now.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.

Washer door and lid lock
A Kenmore washer locks its door or lid while a cycle runs, and it will not spin unless the lock has engaged. The 796 guides print dE for a door or lid left open and dL for a lid lock switch error. Calypso washers print LS for the lid switch, and the 110 front-load guide lists F22 as “Front door lock.”

Washer water inlet screens
Each water valve on a Kenmore washer has a small filter screen where the hot and cold hoses connect. The guides tie them to slow or no filling: Calypso LF (Long Fill) asks whether the inlet valve screens are clear, and the 796 front-load guide says to clean them if the washer does not fill properly.
If the display adds a code.
Door
dE means the lid or door is not closed properly. The 796 top-load displays it if you hit START while the lid is up. Front-loaders in the 796 line show dE1 or dE2 for the same condition, and 110 front-loaders print F22 instead. Close it fully and press START again.
Door
On the Kenmore 796.2927 top-load, dL is the message about the lid's lock switch. Close the lid properly and press START/PAUSE; no spin happens until the lid locks. If dL stays with the lid shut, the guide moves on to service.
Water supply
Kenmore prints F20 on the 110 front-load models 4708 and 4709 and calls it a Water Inlet Problem, meaning no water or too little. Steps: STOP twice, unplug, look at faucets, inlet screens and hoses for kinks or ice, then reconnect, choose the cycle again and press START.
Power
PF means power failure. On a Calypso it flashes: press START to continue the cycle from the moment power was lost, or STOP/CANCEL to clear and cancel. On 796 front-loaders PF shows the next time you turn the washer on, and selecting any cycle clears it.
Read the related care guide.

Washer stops before the spin? Check how it is loaded.
A Kenmore washer stops its spin when the load sits unevenly. Load loosely, mix large and small items, never wash one heavy item alone, and keep the drum from being packed tight. If the washer pauses with an imbalance message, redistribute the load and restart.

Musty front-load washer? Three monthly tasks fix most of it.
Each month, wipe the door seal with the diluted bleach mix, empty the drain pump filter, and leave the door ajar between loads. Check the two inlet filters when the washer fills slowly. All three tasks are in the 796 front-load guide, and each takes only a few minutes.
When observation becomes a service request.
Leave internal testing to a technician.
The washer still will not start with power, a locked lid or door and water confirmed. Book a visit; a 796 top-load clutch error calls for unplugging first.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore washer won't start guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore Calypso top-load washers 110.2206/2408/2506/2508
- Use & Care Guide, Kenmore front-load washers 110.4708/4709
- Use & Care Guide, Kenmore top-load washer 796.2927
Go by the instructions for your exact model. Check how we research these pages.
Why does my Kenmore washer not start?
Power, the lid or door, the START press and water are the guide's four checks. Most no-start calls end at one of them.
Why does my washer fill but not agitate?
The guides do not cover agitation directly. They do list a clutch error on the 796 top-load and an overload code on the Calypso; book a visit if neither fits.
What does F20 mean on a 110 front-load?
A water inlet problem: no water or too little. Check the faucets, the inlet screens, kinked or frozen hoses, then restart.
What does PF mean?
A power failure interrupted the cycle. On the 796 front-load, select any cycle to clear it. On a Calypso, press START to continue or STOP/CANCEL to clear.
Code, symptom, part or service
Link the message to what comes next.
dE
dE means the lid or door is not closed properly. The 796 top-load displays it if you hit START while the lid is up. Front-loaders in the 796 line show dE1 or dE2 for the same condition, and 110 front-loaders print F22 instead. Close it fully and press START again.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer door and lid lock
A Kenmore washer locks its door or lid while a cycle runs, and it will not spin unless the lock has engaged. The 796 guides print dE for a door or lid left open and dL for a lid lock switch error. Calypso washers print LS for the lid switch, and the 110 front-load guide lists F22 as “Front door lock.”
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.