Kenmore washer PF / Power

Kenmore washer
error PF

Washer / display referencePF

PF means power failure. On a Calypso it flashes: press START to continue the cycle from the moment power was lost, or STOP/CANCEL to clear and cancel. On 796 front-loaders PF shows the next time you turn the washer on, and selecting any cycle clears it.

Also shown as PF

Last reviewed

Washer / display referencePF
Meaning
PF means power failure. On a Calypso it flashes: press START to continue the cycle from the moment power was lost, or STOP/CANCEL to clear and cancel. On 796 front-loaders PF shows the next time you turn the washer on, and selecting any cycle clears it.
Who handles it
Owner checks first, then a technician
Related codes
Source
Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

What Kenmore washer PF means.

What it means

PF means power failure. On a Calypso it flashes: press START to continue the cycle from the moment power was lost, or STOP/CANCEL to clear and cancel. On 796 front-loaders PF shows the next time you turn the washer on, and selecting any cycle clears it.

What you can safely check

START carries the cycle on from where it stopped.

When to call a technician

PF appears again without a power interruption.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer PF: Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Calypso: choose START or STOP/CANCEL

    START carries the cycle on from where it stopped. STOP/CANCEL clears the display and cancels the cycle completely.

  2. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 2

    796 front-load: select any cycle

    The code appears when you switch the washer on after an interrupted cycle. Picking a cycle clears it.

  3. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 3

    Look at the tub

    If the cycle did not finish, there may be water and wet laundry inside. Decide whether to rerun it.

  4. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 4

    Think about the outage

    PF is only a message that the earlier cycle may not have completed.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Book a visit if PF appears without an outage

    The guide does not describe PF appearing while power stayed steady.

Still showing PF?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 4Motor wiring

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

A little more context.

What does PF tell me?

It is a notice that power was interrupted during a cycle. On the 796 front-load, the guide says PF displays the next time the washer is turned on, to alert you that the previous cycle may not have completed.

Read the supporting manual

How does the Calypso handle it?

The Calypso asks whether the cycle was interrupted by a power failure, and offers two choices: continue from the moment power was lost, or clear and cancel.

Read the supporting manual

Is PF the same as the dryer PF?

Not exactly. The dryer asks you to press and hold START, and some dryer guides add POWER first. The washer wording differs.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

Kenmore (guide as published by Sears / Transform SR Brands)

Doc L0412465 / P/N 8543703 (Sears, Roebuck and Co.) / PDF p.18

Manufacturer document

Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1909134L / P/N MFL68005592 (Transform SR Brands) / PDF p.46

Manufacturer document

Use & Care Guide, Kenmore front-load washer 796.4198

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1807405L / P/N MFL68005554 / PDF p.31

Calypso 110 washers (guide L0412465 p. 18) and 796 front-loaders (guides 1909134L p. 46 and 1807405L p. 31).

Here to help

Good questions.
Clear answers.

Talk to our team
Should I press START or STOP/CANCEL on a Calypso?

Press START to continue from the moment power was lost, or STOP/CANCEL to clear the display and cancel. START is sensible when the load is only partly done.

Why does a 796 front-load show PF only at the next power-on?

The guide says if power is interrupted during a cycle, PF displays the next time the washer is turned on, to alert you that the cycle may not have finished.

How do I clear PF on a 796 front-load?

Select any cycle. That clears the code and lets you use the washer.

Is PF an error in the washer?

No, it is a notice about the power. Treat it as a prompt to check the load.

What if PF returns without any outage?

Then something other than an outage is interrupting power. Check the outlet and breaker, and book a visit if PF keeps appearing.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.