Start from the symptom
Kenmore washer not spinning.
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Close and latch the lid or door
The 796 guides say the washer will not spin unless the lid or door is locked. Close it firmly and press START/PAUSE. A dE on a 796 top-load means START was pressed with the lid open.
- 2
Rebalance the load
A tiny load needs a couple of matching pieces added; a heavy single piece such as a bath mat or robe needs spreading out. The 796 washer retries the spin several times and then stops with a UE.
- 3
Look at the water in the drum
If the tub is full, the spin cannot start. On the 796 front-load, press POWER, then SPIN SPEED without choosing a cycle, to drain it. Afterward, look for kinks in the drain hose, then clean the drain pump filter.
- 4
Check the drain hose height and the suds
The Calypso guide asks whether the hose end sits more than 96 inches (244 cm) above the floor, and whether there is oversudsing. Use a high-efficiency (HE) detergent and measure it.
- 5
Check the power supply
Calypso washers can stall on low voltage. Plug straight into a grounded outlet; the guide says never to use an extension cord.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.

Washer drain pump filter
The 796 front-load washer has a drain pump filter behind a small access panel. It catches lint, buttons, keys and coins before they reach the pump. When the washer drains slowly or not at all, the guide’s list starts with the drain hose and then this filter.

Washer door and lid lock
A Kenmore washer locks its door or lid while a cycle runs, and it will not spin unless the lock has engaged. The 796 guides print dE for a door or lid left open and dL for a lid lock switch error. Calypso washers print LS for the lid switch, and the 110 front-load guide lists F22 as “Front door lock.”
If the display adds a code.
Balance
UE on a 796 Kenmore washer means the wash load is small or lopsided. Add one or two similar items; the washer makes several attempts to restart the spin and shows the code if it still detects an imbalance.
Drain
OE is the 796 Kenmore message for water that drains slowly, or not at all. Inspect the drain hose for kinks and clogs, clean the drain pump filter, and keep the discharge at 96 inches (244 cm) or less above the bottom of the washer. The top-load guide also lists a drain pump that failed.
Door
dE means the lid or door is not closed properly. The 796 top-load displays it if you hit START while the lid is up. Front-loaders in the 796 line show dE1 or dE2 for the same condition, and 110 front-loaders print F22 instead. Close it fully and press START again.
Door
On the Kenmore 796.2927 top-load, dL is the message about the lid's lock switch. Close the lid properly and press START/PAUSE; no spin happens until the lid locks. If dL stays with the lid shut, the guide moves on to service.
Read the related care guide.

Washer stops before the spin? Check how it is loaded.
A Kenmore washer stops its spin when the load sits unevenly. Load loosely, mix large and small items, never wash one heavy item alone, and keep the drum from being packed tight. If the washer pauses with an imbalance message, redistribute the load and restart.

Musty front-load washer? Three monthly tasks fix most of it.
Each month, wipe the door seal with the diluted bleach mix, empty the drain pump filter, and leave the door ajar between loads. Check the two inlet filters when the washer fills slowly. All three tasks are in the 796 front-load guide, and each takes only a few minutes.
When observation becomes a service request.
Leave internal testing to a technician.
The washer still will not spin with a balanced load, a draining tub and a latched lid or door. The 796 top-load guide describes a clutch error as a mechanical problem: unplug it and arrange a technician. Warranty units go to the manufacturer.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore washer not spinning guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore top-load washer 796.2927
- Use & Care Guide, Kenmore Calypso top-load washers 110.2206/2408/2506/2508
- Use & Care Guide, Kenmore front-load washers 110.4708/4709
Go by the instructions for your exact model. Check how we research these pages.
Why will my Kenmore washer not spin?
The most common reasons in the guides are an unlatched lid or door, an unbalanced load, water still in the drum, or too many suds. Work through them in that order before booking.
What does UE mean on a 796 washer?
The load is too small or out of balance. Add a couple of similar pieces; the washer already tries several times on its own. If UE returns with a mixed, even load, book a visit.
Do suds stop a washer spinning?
Yes. The Calypso guide lists oversudsing under "won't drain or spin" and the front-load guides add a suds-reducing routine. Use only HE detergent and less of it.
The door will not unlock after a stopped cycle. Is that related?
Possibly. The 796 front-load keeps the door locked when the drum is very hot or the water level is high. Let it cool until DOOR LOCK turns off, or drain it as described above.
Code, symptom, part or service
Link the message to what comes next.
UE
UE on a 796 Kenmore washer means the wash load is small or lopsided. Add one or two similar items; the washer makes several attempts to restart the spin and shows the code if it still detects an imbalance.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer door and lid lock
A Kenmore washer locks its door or lid while a cycle runs, and it will not spin unless the lock has engaged. The 796 guides print dE for a door or lid left open and dL for a lid lock switch error. Calypso washers print LS for the lid switch, and the 110 front-load guide lists F22 as “Front door lock.”
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.