Inside the appliance
Washer drain pump filter. In plain English.
The 796 front-load washer has a drain pump filter behind a small access panel. It catches lint, buttons, keys and coins before they reach the pump. When the washer drains slowly or not at all, the guide’s list starts with the drain hose and then this filter.

Where it fits.
Washer drain pump filter in the appliance
In the 796 front-load guide it is behind the filter access panel, which the key parts diagram labels.
The picture shows the type of component. It does not pick out a replacement that fits your model.
What you notice when this system needs attention.
Washer drain pump filter concerns can show up together with weaker performance or a code that keeps returning. Testing is required before deciding whether the component is to blame.

Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.

Kenmore washer shaking
Violent shaking on a Kenmore washer comes down to a lopsided load, feet that are not all touching, shipping bolts left in, or a floor that flexes. Pause, spread the load, check the feet and the bolts, then book us if the shaking persists.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Check the drain hose first
The guide’s drain row lists a kinked, pinched or clogged hose before the filter. It also says the drain discharge may not be more than 96 inches (244 cm) above the bottom of the washer.
- 2
Unplug and let it cool
Before you open the panel, unplug the washer. The guide adds that you should let the water cool if it is hot.
- 3
Clean it as the guide shows
Open the access panel, set the drain hose end in a shallow pan, pull the plug and let the water out. Twist the filter counterclockwise, remove lint and objects, twist it back clockwise, replug the hose and close the panel.
- 4
Clean it now and then
The guide ties a clogged filter to musty smells and says to clean it regularly, not only when the washer stops draining.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if the washer still drains slowly or not at all after the hose and filter are clear.
Book a visit if the 796 top-load shows OE. The guide adds “Drain pump failed” to that row and gives service as the step.
Turn off the taps and unplug the washer if water is leaking.
Arrange a diagnosticSources and model boundaries.
These sources back up the Washer drain pump filter guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore top-load washer 796.2927
Go by the instructions for your exact model. Check how we research these pages.
Where is the drain pump filter?
On the 796 front-load washer it sits behind the filter access panel, which the guide labels in its key parts diagram. Check yours for the exact spot.
Does every Kenmore washer have one?
Not as far as our sources go. We read it in the 796 front-load guides. The other washer guides we read do not use the term drain pump filter.
Why does my washer smell musty?
The 796 guide lists a clogged drain pump filter, residue in the door gasket and a kinked drain hose among the causes. It says to clean the filter regularly and wipe the gasket.
What does OE mean?
On 796 washers OE means water drains slowly or not at all. The guide says to check the drain hose and clean the drain pump filter. The top-load row adds that the drain pump may have failed.
Code, symptom, part or service
Link the message to what comes next.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.

