Start from the symptom
Kenmore washer shaking.
Violent shaking on a Kenmore washer comes down to a lopsided load, feet that are not all touching, shipping bolts left in, or a floor that flexes. Pause, spread the load, check the feet and the bolts, then book us if the shaking persists.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Pause and redistribute the load
The 796 front-load guide says wash shoes, tangled clothes and heavy single loads cause thumping. Pause the cycle, wait for the door to unlock, then spread the items out.
- 2
Check that every foot is on the floor
On the 796 top-load, all four leveling feet must press firmly during the spin with a load in the tub. On a Calypso, the front feet should be installed with the nuts tightened and the rear self-adjusting feet reset if needed.
- 3
Look for shipping bolts and packing
A vibrating noise on the 796 front-load is tied first to shipping bolts or packaging that were never removed. The installation section shows where they sit.
- 4
Test the floor
All the guides want a solid floor. Press and bounce near the washer; a floor that flexes will amplify the movement.
- 5
Know the sounds that are normal
The 796 top-load has a liquid-filled ring that sloshes when the tub stops, and a high-pitched whine at top spin speeds. Neither is a problem.
Systems a technician may investigate.
We don’t quote parts up front. The technician names any part after the diagnostic and matches it to your exact model number before anything is replaced.

Washer door and lid lock
A Kenmore washer locks its door or lid while a cycle runs, and it will not spin unless the lock has engaged. The 796 guides print dE for a door or lid left open and dL for a lid lock switch error. Calypso washers print LS for the lid switch, and the 110 front-load guide lists F22 as “Front door lock.”

Washer drain pump filter
The 796 front-load washer has a drain pump filter behind a small access panel. It catches lint, buttons, keys and coins before they reach the pump. When the washer drains slowly or not at all, the guide’s list starts with the drain hose and then this filter.

Washer water inlet screens
Each water valve on a Kenmore washer has a small filter screen where the hot and cold hoses connect. The guides tie them to slow or no filling: Calypso LF (Long Fill) asks whether the inlet valve screens are clear, and the 796 front-load guide says to clean them if the washer does not fill properly.

Washer drive motor
On 796 Kenmore washers the drive motor is the part behind the LE code. The front-load guide prints LE as “A motor error has occurred,” and the top-load guide says the motor’s thermal overload protection has tripped. Both say to let the washer stand for 30 minutes, then restart.
Read the related care guide.

Washer stops before the spin? Check how it is loaded.
A Kenmore washer stops its spin when the load sits unevenly. Load loosely, mix large and small items, never wash one heavy item alone, and keep the drum from being packed tight. If the washer pauses with an imbalance message, redistribute the load and restart.

Musty front-load washer? Three monthly tasks fix most of it.
Each month, wipe the door seal with the diluted bleach mix, empty the drain pump filter, and leave the door ajar between loads. Check the two inlet filters when the washer fills slowly. All three tasks are in the 796 front-load guide, and each takes only a few minutes.
When observation becomes a service request.
Leave internal testing to a technician.
Walking or banging continues despite a balanced load, level feet and a solid floor. Book a visit and tell us the model prefix (796 or 110) and when the shaking starts in the cycle.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore washer shaking guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore top-load washer 796.2927
- Use & Care Guide, Kenmore Calypso top-load washers 110.2206/2408/2506/2508
Go by the instructions for your exact model. Check how we research these pages.
Why does my Kenmore washer shake during spin?
Spin speed amplifies any imbalance. The guides point to an uneven load first, then feet that are not firmly down, leftover shipping bolts, and a floor that is not rigid.
Is a thumping sound normal?
With heavy loads, the 796 front-load guide calls a thump normal. If it continues, the washer is probably out of balance, so stop it and spread the load.
How do I level a Kenmore washer?
Follow the leveling section of your installation instructions. On a 796 top-load, adjust the feet until all four contact the floor during a loaded spin.
Does shaking mean the motor is failing?
The guides do not say so. They list load, level, bolts and flooring. A motor problem would normally show as LE or another code rather than as shaking alone.
Code, symptom, part or service
Link the message to what comes next.
UE
UE on a 796 Kenmore washer means the wash load is small or lopsided. Add one or two similar items; the washer makes several attempts to restart the spin and shows the code if it still detects an imbalance.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.