Inside the appliance
Washer drive motor. In plain English.
On 796 Kenmore washers the drive motor is the part behind the LE code. The front-load guide prints LE as “A motor error has occurred,” and the top-load guide says the motor’s thermal overload protection has tripped. Both say to let the washer stand for 30 minutes, then restart.

Where it fits.
Washer drive motor in the appliance
The 796 front-load guide says the direct-drive motor is not visible. Neither guide shows it, so there is nothing to inspect from the outside.
The picture shows the type of component. It does not pick out a replacement that fits your model.
What you notice when this system needs attention.
Washer drive motor concerns can show up together with weaker performance or a code that keeps returning. Testing is required before deciding whether the component is to blame.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Let it stand 30 minutes
Both guides give the same first step: allow the washer to stand for 30 minutes before you restart the cycle. The top-load guide says that lets the motor cool.
- 2
Restart the cycle
If LE is gone after the rest, the guides say nothing more. Note when it happened and what load was inside.
- 3
Unplug if it returns
The top-load guide says that if LE appears again you should unplug the washer and get service. The front-load guide says to call for service if the code persists.
- 4
Leave the motor alone
The 796 front-load guide calls its motor a direct-drive motor and notes it is not visible. A care-section warning says the motor, pump, valve and control board are intentionally not grounded and can shock during servicing.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if LE returns after the 30-minute rest.
Book a visit if the drum will not turn and no code shows.
Unplug the washer and keep clear of the motor area.
Arrange a diagnosticSources and model boundaries.
These sources back up the Washer drive motor guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore front-load washer 796.4198
- Use & Care Guide, Kenmore top-load washer 796.2927
Go by the instructions for your exact model. Check how we research these pages.
What does LE mean on a Kenmore washer?
On 796 front-loads it means a motor error. On the 796 top-load it means the motor’s thermal overload protection tripped. Both guides say to let it stand 30 minutes and restart.
Is LE the same on every Kenmore washer?
No. Our sources are the 796 guides only. Other model families may print it differently, so check your model prefix first.
Can I use the washer while LE shows?
The guides say to rest the washer and restart the cycle. They don’t say to keep running it. If LE returns, stop and book a visit.
Is the motor something I can check?
No. The front-load guide notes the motor is not visible, and its warning lists the motor among parts that can shock during servicing.
Code, symptom, part or service
Link the message to what comes next.
LE
On a 796 front-load Kenmore washer, LE means a motor error; on the 796 top-load (2927) it means the motor's thermal overload protection has tripped. Both guides give the same first move: let the washer stand for 30 minutes, then restart the cycle.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.


