Start from the symptom
Kenmore washer drum not turning.
None of the Kenmore guides we read describe belts or pulleys, so we cannot name a cause from them. What they do print: an overloaded Calypso can trip CA or CL, a 796 can show LE after a motor overheats, and a 796 top-load can report a clutch problem.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Check the lid or door lock
The 796 guides say the drum will not spin unless the lid or door is locked. Close it properly and press START/PAUSE.
- 2
Think about the load
A Calypso shows CA or CL (current limit) when overloaded; the guide asks whether you overloaded it and says to press STOP/CANCEL. Wash a smaller load and try again.
- 3
Let the motor cool if LE shows
The 796 guides say to leave the washer standing for 30 minutes and restart the cycle. On the top-load model LE is tied to the motor thermal overload protection.
- 4
Note a clutch message
The 796 top-load guide lists a clutch error as a mechanical failure and says to unplug the washer and arrange service.
- 5
Listen first
Humming with no turning, grinding, or no sound at all tells us different things. Write down what you hear before you call.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.
If the display adds a code.
Motor
On a 796 front-load Kenmore washer, LE means a motor error; on the 796 top-load (2927) it means the motor's thermal overload protection has tripped. Both guides give the same first move: let the washer stand for 30 minutes, then restart the cycle.
Overload
CA is the Calypso washer's current limit message. The guide's question is whether the machine is overloaded, and its remedy is one key press that wipes the display. Take some items out before you start again. A 796 top-load uses CL for something else, so match the code to your model prefix.
Door
On the Kenmore 796.2927 top-load, dL is the message about the lid's lock switch. Close the lid properly and press START/PAUSE; no spin happens until the lid locks. If dL stays with the lid shut, the guide moves on to service.
Read the related care guide.

Washer stops before the spin? Check how it is loaded.
A Kenmore washer stops its spin when the load sits unevenly. Load loosely, mix large and small items, never wash one heavy item alone, and keep the drum from being packed tight. If the washer pauses with an imbalance message, redistribute the load and restart.

Musty front-load washer? Three monthly tasks fix most of it.
Each month, wipe the door seal with the diluted bleach mix, empty the drain pump filter, and leave the door ajar between loads. Check the two inlet filters when the washer fills slowly. All three tasks are in the 796 front-load guide, and each takes only a few minutes.
When observation becomes a service request.
Leave internal testing to a technician.
The drum still does not turn after the lid is latched, the load is lighter and LE has had 30 minutes to clear. Book a visit and tell us your model prefix and any code.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore washer drum not turning guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore top-load washer 796.2927
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore Calypso top-load washers 110.2206/2408/2506/2508
Go by the instructions for your exact model. Check how we research these pages.
Do the Kenmore guides mention drive belts?
The washer guides we checked do not. They cover lid locks, overloads, motor overheating and a clutch error. We will not guess at a belt problem from these documents.
What does LE mean?
On a 796 front-load it is a motor error; on the 796 top-load it means the motor thermal overload tripped. Both guides say wait 30 minutes, then restart.
Can an overloaded washer stop turning?
On a Calypso, yes: CA or CL (current limit) appears, and the guide asks whether the washer is overloaded. Remove items and run a smaller load.
Is it worth running the washer again after an LE?
Once, after the 30-minute rest the guide describes. If LE shows again, book a visit instead of repeating it.
Code, symptom, part or service
Link the message to what comes next.
LE
On a 796 front-load Kenmore washer, LE means a motor error; on the 796 top-load (2927) it means the motor's thermal overload protection has tripped. Both guides give the same first move: let the washer stand for 30 minutes, then restart the cycle.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer drive motor
On 796 Kenmore washers the drive motor is the part behind the LE code. The front-load guide prints LE as “A motor error has occurred,” and the top-load guide says the motor’s thermal overload protection has tripped. Both say to let the washer stand for 30 minutes, then restart.
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.
