Inside the appliance
Washer door and lid lock. In plain English.
A Kenmore washer locks its door or lid while a cycle runs, and it will not spin unless the lock has engaged. The 796 guides print dE for a door or lid left open and dL for a lid lock switch error. Calypso washers print LS for the lid switch, and the 110 front-load guide lists F22 as “Front door lock.”

Where it fits.
Washer door and lid lock in the appliance
The 796 top-load guide’s parts diagram calls it the lid lock; the 796 front-load guide calls it the locking door. It sits where the lid or door closes, and it is not a part to adjust or open.
The picture shows the type of component. It does not pick out a replacement that fits your model.
What you notice when this system needs attention.
Washer door and lid lock concerns can show up together with weaker performance or a code that keeps returning. Testing is required before deciding whether the component is to blame.

Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.

Kenmore washer drum not turning
None of the Kenmore guides we read describe belts or pulleys, so we cannot name a cause from them. What they do print: an overloaded Calypso can trip CA or CL, a 796 can show LE after a motor overheats, and a 796 top-load can report a clutch problem.

Kenmore washer won't start
A Kenmore washer that will not start or agitate is usually missing power, a closed and locked lid or door, a pressed START, or water. Check the plug and breaker, close the lid or door and press START, then confirm the faucets are open.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Close it fully
Both 796 guides start the same way: close the door or lid properly, then press START (front-load) or START/PAUSE (top-load). After you start, the drum may take a few moments to turn, because the washer will not run until the door is locked.
- 2
Let a hot door cool
The 796 front-load guide says the door stays locked when the drum is very hot, for example if a sanitize cycle is paused mid-wash. It calls that normal and says to wait until the DOOR LOCK light on the display goes out.
- 3
Cancel and retry F22
On the 110 front-load guide, F22 reads “Front door lock.” Its step is to select STOP twice to cancel the cycle. It gives no cause, so we don’t guess one.
- 4
Write down the code
Note whether the display shows dE, dE1, dE2, dL, LS or F22, and whether the lid or door was closed when it appeared. A technician can work from that.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if the lid or door is closed and locked and dE or dL still shows. The 796 guides say service is the next step.
Book a visit if the door will not unlock after the washer has cooled and the DOOR LOCK light is off.
Leave the lock and the control behind it to the technician; the guides describe no owner repair.
Arrange a diagnosticSources and model boundaries.
These sources back up the Washer door and lid lock guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore top-load washer 796.2927
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore Calypso top-load washers 110.2206/2408/2506/2508
- Use & Care Guide, Kenmore front-load washers 110.4708/4709
Go by the instructions for your exact model. Check how we research these pages.
What does dE mean on a Kenmore washer?
On the 796 top-load, dE appears when you press START with the lid open. Front-loads show dE1 or dE2 for a door that is not closed properly. Close it and press START again.
What does dL mean?
On the 796 top-load, dL is a lid lock switch error. Close the lid and press START/PAUSE. If the lid is closed and locked and dL stays, the guide’s next step is service.
Why will my front-load door not open?
The 796 guide says the door stays locked while the drum is very hot, such as after a paused sanitize cycle. Wait for the DOOR LOCK light to go out. If the water level is too high, the guide says press POWER, then SPIN SPEED without selecting a cycle, to drain it.
What does LS mean on a Calypso washer?
LS is the lid switch error. If the lid is open, close it and press START. If it is already closed, open and close it, then press STOP/CANCEL to clear the display.
Code, symptom, part or service
Link the message to what comes next.
dL
On the Kenmore 796.2927 top-load, dL is the message about the lid's lock switch. Close the lid properly and press START/PAUSE; no spin happens until the lid locks. If dL stays with the lid shut, the guide moves on to service.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.

