Kenmore washer LS / Door

Kenmore washer
error LS

Washer / display referenceLS

LS (Lid Switch Error) on a Calypso Kenmore washer flashes when the lid is open or the washer cannot tell it is closed. Close an open lid and press START; if it was already closed, open and close it once, then press STOP/CANCEL.

Also shown as LS

Last reviewed

Washer / display referenceLS
Meaning
LS (Lid Switch Error) on a Calypso Kenmore washer flashes when the lid is open or the washer cannot tell it is closed. Close an open lid and press START; if it was already closed, open and close it once, then press STOP/CANCEL.
Who handles it
Owner checks first, then a technician
Related codes
Source
Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

What Kenmore washer LS means.

What it means

LS (Lid Switch Error) on a Calypso Kenmore washer flashes when the lid is open or the washer cannot tell it is closed. Close an open lid and press START; if it was already closed, open and close it once, then press STOP/CANCEL.

What you can safely check

Is it open?

When to call a technician

LS keeps appearing with the lid closed.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer LS: Close view of a front-load washer's door latch strike on the frame and the hook on the open glass door, with the power cord's plug lying on the laundry counter
    Illustration. Follow your model’s instructions.
    Before you begin

    Look at the lid

    Is it open? Close it and press START to carry on with the cycle.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Open and close the lid once more

    If the lid looked shut, open it fully and close it again to reseat it.

  3. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 3

    Press STOP/CANCEL

    Clear the display after reseating the lid.

  4. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 4

    Keep hands out of the tub

    Never reach into the basket while the washer is running.

  5. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 5

    Watch for a pattern

    If LS comes on every cycle, stop forcing the lid and book a visit.

Still showing LS?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

The door and its lock.

Conceptual Washer sectionDoor / lidDoor lockControl123

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Parts behind the message.

Washer lid lock switch assembly with a plunger on top and two metal terminals, resting on a wooden workbench.

Component reference

Washer door and lid lock

A Kenmore washer locks its door or lid while a cycle runs, and it will not spin unless the lock has engaged.

Read the definition

A little more context.

What does the lid switch do?

It tells the control whether the lid is closed so the washer does not agitate or spin with the lid open. LS says the control did not get a closed signal.

Read the supporting manual

Does closing the lid restart the washer?

The same guide page notes that after opening the lid mid-cycle, the washer stops, and closing the lid will not restart it. You must press START.

Read the supporting manual

How is LS different from dL?

LS is the Calypso lid switch. dL is the 796 top-load lid lock switch. Same area, different families and different button sequences.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

Kenmore (guide as published by Sears / Transform SR Brands)

Doc L0412465 / P/N 8543703 (Sears, Roebuck and Co.) / PDF p.18

Calypso washers 110.2206, 2408, 2506; LS is on p. 18 of guide L0412465.

Here to help

Good questions.
Clear answers.

Talk to our team
What does the lid switch do?

It tells the control whether the lid is closed. LS means the control did not see a closed lid.

Do I need to press START after closing the lid?

Yes. The guide's page says closing the lid does not restart a stopped washer. You must press START.

Why open and close the lid if it was already closed?

The guide asks you to open and close it, then press STOP/CANCEL, to reseat the lid and clear the display.

Is LS the same as SL?

No. SL is Suds Lock. LS is the lid switch message.

When should I call for LS?

When it keeps appearing on closed-lid cycles. Do not force or tape the lid.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.