Model-specific code library

Kenmore washer error codes.

We decode LE, dE, LF, FL, dL, Sd, CA/CL, CE, LS and Ld as pages, plus 11 shorter rows, each tied to the 110 Calypso, 110 front-load or 796 family that prints it.

Washer code finder

On a 796 front-load Kenmore washer, LE means a motor error; on the 796 top-load (2927) it means the motor's thermal overload protection has tripped. Both guides give the same first move: let the washer stand for 30 minutes, then restart the cycle.

Read the LE checks
Or choose

29 researched washer codes. A code can mean different things on different models, so read it against your own manual.

Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work

Messages with a manual behind them.

CA

Overload

CA is the Calypso washer's current limit message. The guide's question is whether the machine is overloaded, and its remedy is one key press that wipes the display. Take some items out before you start again. A 796 top-load uses CL for something else, so match the code to your model prefix.

Owner checks first
CE

Communication

CE is the Calypso's Communications Error message. The code flashes and the washer beeps once. Wipe the display with STOP/CANCEL; a CE that keeps occurring is a service matter. No cause is named, so the owner has no repair to attempt.

Model-dependent / read first
CL

Overload

CL has two meanings on Kenmore washers. On a 110 Calypso it means Current Limit: the guide asks whether the washer is overloaded and says to press STOP/CANCEL. On a 796 top-load it means Control Lock is on, which is not a problem.

Owner checks first
dE

Door

dE means the lid or door is not closed properly. The 796 top-load displays it if you hit START while the lid is up. Front-loaders in the 796 line show dE1 or dE2 for the same condition, and 110 front-loaders print F22 instead. Close it fully and press START again.

Owner checks first
dE1

Door

In the Kenmore 796 front-load guides, dE1 is a display graphic printed beside the door-not-closed text. The guides do not say how it differs from dE2. Close the door until it latches, then press START/PAUSE.

Owner checks first
dE2

Door

dE2 turns up in the same 796 front-load guides as dE1, beside the door text. No guide separates the two. Shut the door firmly and press START/PAUSE; if the open-door message stays, book a technician.

Owner checks first
dL

Door

On the Kenmore 796.2927 top-load, dL is the message about the lid's lock switch. Close the lid properly and press START/PAUSE; no spin happens until the lid locks. If dL stays with the lid shut, the guide moves on to service.

Owner checks first
Er

Electronics

The Calypso shows Er for a Processor Reset Error: the cycle information was not stored during a power failure. Clear the display with STOP/CANCEL, then set the cycle up again from scratch.

Owner checks first
F02

Drain

F02 is printed as Drain Problem in the Kenmore 110.4292, 4492 and 4493 front-load guide. Cancel with PAUSE/CANCEL twice, unplug the washer and examine the drain hose for kinks, ice, clogs and a height over 96 inches. After that, reconnect, select the cycle once more and press START.

Owner checks first
F20

Water supply

Kenmore prints F20 on the 110 front-load models 4708 and 4709 and calls it a Water Inlet Problem, meaning no water or too little. Steps: STOP twice, unplug, look at faucets, inlet screens and hoses for kinks or ice, then reconnect, choose the cycle again and press START.

Owner checks first
F21

Drain

F21 is printed as Drain Problem on Kenmore 110.4708 and 4709 front-loaders. STOP twice, then unplug and ask four things of the drain hose: kinked, frozen, clogged, or higher than 96 inches? Reconnect and restart afterward.

Owner checks first
F22

Door

Kenmore 110 front-loaders 4708 and 4709 print F22 under the label Front door lock. Cancel with STOP twice, then reopen the door and close it firmly; a door can look shut and still be unlatched. Check for laundry sticking out and reduce an overloaded basket.

Owner checks first
FE

Water supply

FE means the water level is too high, and the 796 guides tie it to a faulty water valve. Turn off both faucets, unplug and call for service. It is an urgent one: do not leave water flowing into the tub.

Act now
FH

Water supply

On Kenmore 110 front-loaders 4292, 4492 and 4493, FH is the Water Inlet Problem label: no water, or an insufficient supply. Hit PAUSE/CANCEL twice, unplug, then check faucets, screens and hoses before you reconnect and restart the cycle.

Owner checks first
FL

Leak

The Calypso's FL (Over Fill) message means the over fill switch tripped. The washer beeps every 10 seconds and the pump cycles half a minute on and half a minute off until the switch resets or power is cut. If water keeps flowing, shut off the faucets to both inlet hoses.

Act now
IE

Water supply

On 796 Kenmore washers, IE signals a slow fill or no fill. Faucets fully open, hoses straight, inlet filters clean and house pressure adequate are the guides' checks. The front-load guide also advises against leak-limiting hoses.

Owner checks first
Ld

Drain

Ld (Long Drain) is the Calypso's slow-drain message. The guide asks if the drain hose is kinked or clogged and says STOP/CANCEL clears the display. The 110 front-loaders print F21 and F02 for a drain problem instead.

Owner checks first
LE

Motor

On a 796 front-load Kenmore washer, LE means a motor error; on the 796 top-load (2927) it means the motor's thermal overload protection has tripped. Both guides give the same first move: let the washer stand for 30 minutes, then restart the cycle.

Owner checks first
LF

Water supply

LF (Long Fill) tells you a Calypso took too long to fill. Its two questions are whether the inlet hoses are kinked or clogged and whether the inlet valve screens are clear; STOP/CANCEL then clears the display.

Owner checks first
LS

Door

LS (Lid Switch Error) on a Calypso Kenmore washer flashes when the lid is open or the washer cannot tell it is closed. Close an open lid and press START; if it was already closed, open and close it once, then press STOP/CANCEL.

Owner checks first
OE

Drain

OE is the 796 Kenmore message for water that drains slowly, or not at all. Inspect the drain hose for kinks and clogs, clean the drain pump filter, and keep the discharge at 96 inches (244 cm) or less above the bottom of the washer. The top-load guide also lists a drain pump that failed.

Owner checks first
Or

Control

For Or (Open Relay) the Calypso guide offers just the words washer operation failure and an instruction to call for service. Nothing is left to try at home; jot the code down and book a technician.

Book a visit
PE

Water level

PE means the water level sensor is not working correctly on 796 Kenmore washers. Both guides ask you to turn off the faucets, unplug and call. Owners have nothing to repair here, so book a technician.

Book a visit
PF

Power

PF means power failure. On a Calypso it flashes: press START to continue the cycle from the moment power was lost, or STOP/CANCEL to clear and cancel. On 796 front-loaders PF shows the next time you turn the washer on, and selecting any cycle clears it.

Owner checks first
Sd

Suds

Sd is the suds message: the control sensed more foam than it should. On 110 front-loaders the display shows SUD and a suds routine starts on its own. On 796 front-loaders it shows Sud and adds a Suds Reducing cycle of about two hours. Use less detergent next time.

Owner checks first
SL

Suds

SL (Suds Lock) is the Calypso's way of saying it found too many suds. STOP/CANCEL wipes the display, and the next load should get less detergent.

Owner checks first
Sr

Control

The Calypso guide is just as terse about Sr (Stuck Relay), giving the phrase operation failure plus a service instruction. Owners get no step here, so record Sr and book a technician.

Book a visit
tE

Temperature

tE means a control error on 796 front-loaders and a thermistor error, the water temperature sensor, on the 796 top-load. On a front-load, unplug the washer, wait 60 seconds, reconnect and try again. On a top-load, unplug and book service.

Owner checks first
UE

Balance

UE on a 796 Kenmore washer means the wash load is small or lopsided. Add one or two similar items; the washer makes several attempts to restart the spin and shows the code if it still detects an imbalance.

Owner checks first

Models made under the 2026 Curtis International license are not covered yet. uL, F01, oL, dU, F29, F26 and F27 are not printed in any Kenmore guide we read. The 796 top-load clutch row could not be read at the page resolution we used, so it is not included.

Start with the model boundary.

Washers in a thoughtfully designed home

Each washer family prints its own codes.

We decode LE, dE, LF, FL, dL, Sd, CA/CL, CE, LS and Ld as pages, plus 11 shorter rows, each tied to the 110 Calypso, 110 front-load or 796 family that prints it.

Models made under the 2026 Curtis International license are not covered yet. uL, F01, oL, dU, F29, F26 and F27 are not printed in any Kenmore guide we read. The 796 top-load clutch row could not be read at the page resolution we used, so it is not included.

Choose the next safe action.

Read the whole display

Give the model prefix (110, 796 or Calypso) and the exact code. The same letters, such as tE, CL and F02, mean different things between families.

Respect the service boundary

Close the water faucets and unplug the washer if water escapes, the FL or FE codes show, or the washer will not stop filling. Leave motors, lid locks and boards to a technician.

Documents checked for this library.

  • Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
  • Use & Care Guide, Kenmore front-load washer 796.4198
  • Use & Care Guide, Kenmore top-load washer 796.2927
  • Use & Care Guide, Kenmore front-load washers 110.4708/4709
  • Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508
  • Use & Care Guide, Kenmore front-load washers 110.4292/4492/4493

Go by the instructions for your exact model. Check how we research these pages.

Here to help

Good questions.
Clear answers.

Talk to our team
Are these washer meanings universal?

Models made under the 2026 Curtis International license are not covered yet. uL, F01, oL, dU, F29, F26 and F27 are not printed in any Kenmore guide we read. The 796 top-load clutch row could not be read at the page resolution we used, so it is not included.

What details should I include for a washer code?

Take a photo of the entire washer display and of the model label. Note what the appliance was doing when the message came up, instead of borrowing an explanation written for a different appliance.

Why does a washer message appear with no meaning next to it?

An old search phrase is no proof of what a code means. If our washer manuals do not explain a message, we list the name as it appears and send you toward help, without blaming a part or a cause.

How do I confirm which washer models a page covers?

Open the manuals in this washer library and match the models on their covers to the label on your appliance. A model that is not listed there needs its own operating instructions.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.