Kenmore washer PE / Water level

Kenmore washer
error PE

Washer / display referencePE

PE means the water level sensor is not working correctly on 796 Kenmore washers. Both guides ask you to turn off the faucets, unplug and call. Owners have nothing to repair here, so book a technician.

Also shown as PE

Last reviewed

Washer / display referencePE
Meaning
PE means the water level sensor is not working correctly on 796 Kenmore washers. Both guides ask you to turn off the faucets, unplug and call. Owners have nothing to repair here, so book a technician.
Who handles it
Book a visit
Related codes
Source
Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156

What Kenmore washer PE means.

What it means

PE means the water level sensor is not working correctly on 796 Kenmore washers. Both guides ask you to turn off the faucets, unplug and call. Owners have nothing to repair here, so book a technician.

What you can safely check

Shut off the supply first.

When to call a technician

PE shows at all.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer PE: Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Close the faucets

    Shut off the supply first.

  2. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 2

    Unplug the washer

    Use the breaker if the floor is wet.

  3. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 3

    Leave the tub alone

    Do not try to adjust any sensor or hose in the tub.

  4. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 4

    Note the load and cycle

    Tell the technician what the washer was doing.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    Quote PE and the model number.

Still showing PE?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub
  2. 4Drain pump

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Parts behind the message.

Front-load washer with its door open on a laundry room floor, a shallow pool of water visible at the bottom of the stainless steel drum.

Component reference

Washer water level sensor

A 796 Kenmore washer relies on its water level sensor to judge the fill.

Read the definition

A little more context.

What does PE mean?

The 796 troubleshooting list reads The water level sensor is not working correctly, with the close-the-faucets and unplug steps.

Read the supporting manual

Is it dangerous?

The guide does not call it dangerous, but it does ask you to shut the faucets and unplug before calling, so treat it with care.

Read the supporting manual

How is PE different from FE?

FE blames the water valve and PE the level sensor. Both ask for the same steps.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1909134L / P/N MFL68005592 (Transform SR Brands) / PDF p.46

Manufacturer document

Use & Care Guide, Kenmore front-load washer 796.4198

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1807405L / P/N MFL68005554 / PDF p.31

Manufacturer document

Use & Care Guide, Kenmore top-load washer 796.2927

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1007244L / P/N MFL42065471 / PDF p.28

Same two 796 tables: front-load p. 46 of guide 1909134L, top-load p. 27 of guide 1007244L.

Here to help

Good questions.
Clear answers.

Talk to our team
What does the water level sensor do?

It lets the control judge the water depth in the tub. PE says the sensor is not working correctly.

Can I restart the cycle after closing the faucets?

Unplug and call is the advice given. Do not restart it.

Is PE the same as PF?

No. PF is a power failure notice. PE is a water level sensor message.

Is there a reset?

None is printed for PE.

What should I report?

The code PE, your model number and the stage the washer was in.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.