Kenmore washer FE / Water supply

Kenmore washer
error FE

Washer / display reference

FE means the water level is too high, and the 796 guides tie it to a faulty water valve. Turn off both faucets, unplug and call for service. It is an urgent one: do not leave water flowing into the tub.

Also shown as FE

Last reviewed

Washer / display reference
Meaning
FE means the water level is too high, and the 796 guides tie it to a faulty water valve. Turn off both faucets, unplug and call for service. It is an urgent one: do not leave water flowing into the tub.
Who handles it
Technician — close the water supply
Related codes
Source
Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156

What Kenmore washer FE means.

What it means

FE means the water level is too high, and the 796 guides tie it to a faulty water valve. Turn off both faucets, unplug and call for service. It is an urgent one: do not leave water flowing into the tub.

What you can safely check

Shut off the water supply first.

When to call a technician

FE shows at all.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer FE: Hand holding a small mesh screen removed from the washer's inlet, with the detached red and blue hoses and the unplugged cord on the counter below
    Illustration. Follow your model’s instructions.
    Before you begin

    Close both faucets

    Shut off the water supply first. Water entering the tub is the risk.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Unplug the washer

    With a wet floor, go to the breaker rather than the plug.

  3. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 3

    Do not run another cycle

    The guide has no owner repair for the valve.

  4. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 4

    Look for leaks and standing water

    Check the floor and the hose connections.

  5. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit

    Say that FE appeared and that the water was shut off.

Still showing FE?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

Water into the washer.

Conceptual Washer sectionSupply valveInlet hoseTub inlet123
  1. 1Supply valve
  2. 3Tub inlet

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Parts behind the message.

Back of a washer with two braided steel hoses connected to the red and blue inlet ports and running to wall shutoff valves, one hand turning a valve handle.

Component reference

Washer water inlet valve

The washer water inlet valve is where hot and cold water enter a Kenmore washer, and its filter screens trap debris.

Read the definition

A little more context.

What does FE mean?

The 796 guides list a display of FE with the cause water level is too high due to a faulty water valve. The remedy: faucets off, washer unplugged, then a call.

Read the supporting manual

Why shut the faucets first?

If the valve is stuck open, water can keep coming in. Closing the faucets stops the supply at the wall.

Read the supporting manual

How is FE different from PE?

PE is the water level sensor. FE is the water valve. Both advise the same faucet-and-unplug steps.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1909134L / P/N MFL68005592 (Transform SR Brands) / PDF p.46

Manufacturer document

Use & Care Guide, Kenmore front-load washer 796.4198

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1807405L / P/N MFL68005554 / PDF p.31

Manufacturer document

Use & Care Guide, Kenmore top-load washer 796.2927

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1007244L / P/N MFL42065471 / PDF p.27

The FE row appears in the 796 tables of guides 1909134L (p. 46, front-load) and 1007244L (p. 27, top-load).

Here to help

Good questions.
Clear answers.

Talk to our team
Why close the faucets before anything else?

The guide ties FE to a water valve problem and a water level that is too high. Closing the faucets stops more water entering.

May I run a rinse to empty the tub?

We would not. Unplug the washer and wait for the technician, who can drain it safely.

Is FE on 110 washers too?

Not in the guides we read. Calypso washers use FL for over fill.

How is FE different from PE?

FE blames the water valve. PE blames the water level sensor. Both give the same faucet-and-unplug advice.

What goes in the booking notes?

FE, the model number, that the faucets were closed and the washer unplugged, and any water you saw on the floor.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.