What it means
CL has two meanings on Kenmore washers. On a 110 Calypso it means Current Limit: the guide asks whether the washer is overloaded and says to press STOP/CANCEL. On a 796 top-load it means Control Lock is on, which is not a problem.
Kenmore washer CL / Overload
CL has two meanings on Kenmore washers. On a 110 Calypso it means Current Limit: the guide asks whether the washer is overloaded and says to press STOP/CANCEL. On a 796 top-load it means Control Lock is on, which is not a problem.
Also shown as CL
CL has two meanings on Kenmore washers. On a 110 Calypso it means Current Limit: the guide asks whether the washer is overloaded and says to press STOP/CANCEL. On a 796 top-load it means Control Lock is on, which is not a problem.
The guide asks "Is the washer overloaded?" Remove some items if so.
CL returns on a Calypso after the load has been reduced and the display cleared.
Your checklist / stored on this device

The guide asks "Is the washer overloaded?" Remove some items if so.

This clears the display so you can start again.

If CL alternates with the remaining cycle time, press and hold DRAIN & SPIN for 5 seconds. Every control except CONTROL LOCK and POWER is disabled until then.
Give us the model and the checks you have already done, and open your request from here.
Book a visitSimplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.
CL has two meanings on Kenmore washers. On a 110 Calypso it means Current Limit: the guide asks whether the washer is overloaded and says to press STOP/CANCEL. On a 796 top-load it means Control Lock is on, which is not a problem.
Read the supporting manualCheck the load size (Calypso). The guide asks "Is the washer overloaded?" Remove some items if so.
Read the supporting manualCL returns on a Calypso after the load has been reduced and the display cleared.
Read the supporting manualManufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc L0412465 / P/N 8543703 (Sears, Roebuck and Co.) / PDF p.18
Manufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc 1007244L / P/N MFL42065471 / PDF p.22 (Control Lock)
CA/CL as Current Limit is printed for the 110 Calypso (110.2206, 110.2408, 110.2506). CL as Control Lock is printed for the 796 top-load 2927. Check the prefix on your model label before you decide which one applies.
On a 110 Calypso, CL means Current Limit. On a 796 top-load, CL means Control Lock is on. Check the model prefix on your label to see which applies.
If CL alternates with the remaining cycle time, press and hold DRAIN & SPIN for 5 seconds. Every control except CONTROL LOCK and POWER is disabled until then.
On a Calypso the guide prints CA or CL for Current Limit. On a 796 top-load, CL is Control Lock and CA is not printed.
No. Current Limit points to an overloaded washer, and Control Lock is a setting. Lighten the load or release the lock first.
Code, symptom, part or service
CA is the Calypso washer's current limit message. The guide's question is whether the machine is overloaded, and its remedy is one key press that wipes the display. Take some items out before you start again. A 796 top-load uses CL for something else, so match the code to your model prefix.
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Book a diagnostic for your model, carried out at the appliance.
Office details, and the access information to pass along.