Kenmore washer FL / Leak

Kenmore washer
error FL

Washer / display referenceFL

The Calypso's FL (Over Fill) message means the over fill switch tripped. The washer beeps every 10 seconds and the pump cycles half a minute on and half a minute off until the switch resets or power is cut. If water keeps flowing, shut off the faucets to both inlet hoses.

Also shown as FL

Last reviewed

Washer / display referenceFL
Meaning
The Calypso's FL (Over Fill) message means the over fill switch tripped. The washer beeps every 10 seconds and the pump cycles half a minute on and half a minute off until the switch resets or power is cut. If water keeps flowing, shut off the faucets to both inlet hoses.
Who handles it
Technician — close the water supply
Related codes
Source
Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

What Kenmore washer FL means.

What it means

The Calypso's FL (Over Fill) message means the over fill switch tripped. The washer beeps every 10 seconds and the pump cycles half a minute on and half a minute off until the switch resets or power is cut. If water keeps flowing, shut off the faucets to both inlet hoses.

What you can safely check

When water carries on running into the tub, begin by closing the supply to the inlet hoses.

When to call a technician

FL returns, water keeps flowing with the faucets closed, or there is water on the floor.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer FL: Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Close both water faucets

    When water carries on running into the tub, begin by closing the supply to the inlet hoses. The guide gives this step.

  2. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 2

    Press STOP/CANCEL

    This clears the display. Beeping and pump cycling can continue until the switch resets.

  3. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 3

    Cut power if it will not stop

    If the beeping carries on, cut power. With water on the floor, use the breaker, not the plug.

  4. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 4

    Check the floor and the hoses

    Look for leaks at the hose connections and puddles around the washer.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Book a visit if FL returns

    A repeat means the water level control needs a technician.

Still showing FL?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

Fill and the water level.

Conceptual Washer sectionInlet valveTubLevel sensorDrain pump1234
  1. 2Tub

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

A little more context.

What is the over fill switch?

The guide calls it the over fill switch and says FL appears when it trips. The washer then beeps every 10 seconds with no time-out.

Read the supporting manual

What is the pump doing?

The pump cycles one half minute on and one half minute off until the switch resets or power is discontinued, per the guide. That cycling pumps water out.

Read the supporting manual

How is FL different from LF?

FL is the over fill alarm. LF is Long Fill, a tub that is slow to fill. They are opposites in the sense of water coming in.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

Kenmore (guide as published by Sears / Transform SR Brands)

Doc L0412465 / P/N 8543703 (Sears, Roebuck and Co.) / PDF p.18 (Troubleshooting)

Calypso washers 110.2206, 2408, 2506; FL (Over Fill) is on p. 18 of guide L0412465.

Here to help

Good questions.
Clear answers.

Talk to our team
Why does the washer beep every 10 seconds?

Per the guide, the FL signal beeps every 10 seconds with no time-out and cycles the pump half a minute on, half a minute off until the over fill switch resets or power is cut.

What should I do first?

Close the faucets to both inlet hoses if water keeps flowing, then press STOP/CANCEL.

Is FL an emergency?

It can be, if water keeps entering. Treat water on the floor or flow with the faucets closed as urgent and call a technician.

How is FL different from FE?

FE is the 796 message about a faulty water valve. FL is the Calypso over fill switch.

Is F27 the same as FL?

An old web address mentioned F27. No Kenmore guide we read prints it, so we give it no meaning.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.