What it means
LF (Long Fill) tells you a Calypso took too long to fill. Its two questions are whether the inlet hoses are kinked or clogged and whether the inlet valve screens are clear; STOP/CANCEL then clears the display.
Kenmore washer LF / Water supply
LF (Long Fill) tells you a Calypso took too long to fill. Its two questions are whether the inlet hoses are kinked or clogged and whether the inlet valve screens are clear; STOP/CANCEL then clears the display.
Also shown as LF
LF (Long Fill) tells you a Calypso took too long to fill. Its two questions are whether the inlet hoses are kinked or clogged and whether the inlet valve screens are clear; STOP/CANCEL then clears the display.
Shut off both supply faucets so a loosened hose does not spray.
LF keeps coming back after the hoses and screens are clear.
Your checklist / stored on this device

Shut off both supply faucets so a loosened hose does not spray.

Look at both hoses behind the washer for kinks or crushed sections.

The guide asks if the screens are clear. Clean any grit or sediment from them.

Clear the display, reopen the faucets and run the cycle.

If another tap runs weakly, supply pressure may be the issue. This is general advice, not part of the Calypso list.
Give us the model and the checks you have already done, and open your request from here.
Book a visitSimplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Component reference
Each water valve on a Kenmore washer has a small filter screen where the hot and cold hoses connect.
Read the definition
Component reference
The washer water inlet valve is where hot and cold water enter a Kenmore washer, and its filter screens trap debris.
Read the definitionThe guide labels it Long Fill and asks two questions, about the hoses and about the screens. The washer is saying the tub did not fill in the expected time.
Read the supporting manualSmall screens at the inlet valve catch grit from the supply. Over time they can restrict flow. The guide only asks if they are clear.
Read the supporting manualLF is slow filling. FL is the over fill switch. The same tub, opposite problems.
Read the supporting manualManufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc L0412465 / P/N 8543703 (Sears, Roebuck and Co.) / PDF p.18 (Troubleshooting)
LF is printed on p. 18 of guide L0412465 for the 110.2206, 2408, 2506 and 2508.
A small filter screen where the hose meets the washer, which can clog with grit. The guide asks whether those screens are clear.
No. LF reports a fill that dragged on. If no water arrives at all, check the faucets, the hoses and the screens.
The Calypso list does not name pressure. The 796 guides do, under IE.
Press STOP/CANCEL to clear the display, then try the cycle again.
No. FL is the over fill switch and means too much water. LF means too slow a fill.
Code, symptom, part or service
The Calypso's FL (Over Fill) message means the over fill switch tripped. The washer beeps every 10 seconds and the pump cycles half a minute on and half a minute off until the switch resets or power is cut. If water keeps flowing, shut off the faucets to both inlet hoses.
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Each water valve on a Kenmore washer has a small filter screen where the hot and cold hoses connect. The guides tie them to slow or no filling: Calypso LF (Long Fill) asks whether the inlet valve screens are clear, and the 796 front-load guide says to clean them if the washer does not fill properly.
Book a diagnostic for your model, carried out at the appliance.
Office details, and the access information to pass along.