Kenmore washer F20 / Water supply

Kenmore washer
error F20

Washer / display reference

Kenmore prints F20 on the 110 front-load models 4708 and 4709 and calls it a Water Inlet Problem, meaning no water or too little. Steps: STOP twice, unplug, look at faucets, inlet screens and hoses for kinks or ice, then reconnect, choose the cycle again and press START.

Also shown as F20

Last reviewed

Washer / display reference
Meaning
Kenmore prints F20 on the 110 front-load models 4708 and 4709 and calls it a Water Inlet Problem, meaning no water or too little. Steps: STOP twice, unplug, look at faucets, inlet screens and hoses for kinks or ice, then reconnect, choose the cycle again and press START.
Who handles it
Owner checks first, then a technician
Related codes
Source
Use & Care Guide, Kenmore front-load washers 110.4708/4709

What Kenmore washer F20 means.

What it means

Kenmore prints F20 on the 110 front-load models 4708 and 4709 and calls it a Water Inlet Problem, meaning no water or too little. Steps: STOP twice, unplug, look at faucets, inlet screens and hoses for kinks or ice, then reconnect, choose the cycle again and press START.

What you can safely check

This cancels the cycle.

When to call a technician

F20 outlasts the supply checks.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer F20: Hand holding a small mesh screen removed from the washer's inlet, with the detached red and blue hoses and the unplugged cord on the counter below
    Illustration. Follow your model’s instructions.
    Before you begin

    Select STOP twice

    This cancels the cycle. Do not unplug first if the display is still responding.

  2. Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Check 2

    Unplug or disconnect power

    Then check that both water faucets are completely on.

  3. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 3

    Check the inlet screens and hoses

    Inspect the screens where the hoses meet the washer for clogs, and look along the hoses for bends and ice.

  4. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 4

    Reconnect, re-select, press START

    The cycle must be selected again before it will start.

  5. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 5

    Book a visit if F20 remains

    If the problem remains, service is the guide's last step.

Still showing F20?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

Water into the washer.

Conceptual Washer sectionSupply valveInlet hoseTub inlet123
  1. 1Supply valve
  2. 3Tub inlet

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Parts behind the message.

Two small round mesh inlet screens beside a braided steel washer hose with brass couplings, on a wooden workbench.

Component reference

Washer water inlet screens

Each water valve on a Kenmore washer has a small filter screen where the hot and cold hoses connect.

Read the definition

A little more context.

What does F20 mean?

It reports a supply shortfall: little or no water arriving at the washer. The checks all concern the supply side.

Read the supporting manual

What does the guide say about other F codes?

Other F codes sit under a separate heading with their own steps.

Read the supporting manual

How is F20 different from FH?

FH is the same Water Inlet Problem on the 4292 family, with PAUSE/CANCEL instead of STOP. Both ask for the same supply checks.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore front-load washers 110.4708/4709

Kenmore (guide as published by Sears / Transform SR Brands)

Doc L0809415 / P/N 8183014B / PDF p.22

110 front-loaders 4708 and 4709; troubleshooting on p. 22 of guide L0809415.

Here to help

Good questions.
Clear answers.

Talk to our team
What counts as insufficient water supply?

The guide groups no water and not enough water under one label. Check faucets, screens, kinks and ice before anything else.

Where are the inlet screens?

Where each hose meets the washer. Turn off the faucets before you take a hose off.

How is the cycle canceled?

STOP twice, per the guide, then cut the power.

Is F20 the same as FH?

The wording is identical, but FH is printed for the 4292 family and F20 for the 4708 and 4709.

Does F20 mean the fill valve is dead?

The guide does not say. Its checks are on the supply side, with service after them.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.