Kenmore washer tE / Temperature

Kenmore washer
error tE

Washer / display referencetE

tE means a control error on 796 front-loaders and a thermistor error, the water temperature sensor, on the 796 top-load. On a front-load, unplug the washer, wait 60 seconds, reconnect and try again. On a top-load, unplug and book service.

Also shown as tE

Last reviewed

Washer / display referencetE
Meaning
tE means a control error on 796 front-loaders and a thermistor error, the water temperature sensor, on the 796 top-load. On a front-load, unplug the washer, wait 60 seconds, reconnect and try again. On a top-load, unplug and book service.
Who handles it
Owner checks first, then a technician
Related codes
Source
Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156

What Kenmore washer tE means.

What it means

tE means a control error on 796 front-loaders and a thermistor error, the water temperature sensor, on the 796 top-load. On a front-load, unplug the washer, wait 60 seconds, reconnect and try again. On a top-load, unplug and book service.

What you can safely check

Reconnect power and try again.

When to call a technician

tE returns after the 60-second wait, or on a top-load at all.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer tE: Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Front-load: unplug for 60 seconds

    Reconnect power and try again. The guide gives the exact interval.

  2. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 2

    Top-load: unplug the washer

    The guide says the water temperature sensor is not working correctly.

  3. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 3

    Do not run more cycles on a top-load

    No owner step is given for the sensor.

  4. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 4

    Note which layout you have

    The meaning changes with the layout.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Book a visit if tE returns

    A front-load code that returns after the wait needs service.

Still showing tE?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

Water heating and its sensor.

Conceptual Washer sectionHeaterTemperature sensorControl123
  1. 1Heater
  2. 2Temperature sensor

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Parts behind the message.

Blue-gloved fingertip pressing a lit key on a washer control panel with a dial and a glowing display reading 45

Component reference

Washer electronic control

The electronic control runs the cycles on a Kenmore washer and reads the keys and display.

Read the definition

A little more context.

What does tE mean on a front-load?

The 796 front-load list reads Control error and asks you to unplug the washer, wait 60 seconds, reconnect and try again. If the error reappears, call for service.

Read the supporting manual

What does tE mean on a top-load?

The 2927 guide calls it a thermistor error: the water temperature sensor is faulty. The remedy is unplug and call.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1909134L / P/N MFL68005592 (Transform SR Brands) / PDF p.46

Manufacturer document

Use & Care Guide, Kenmore front-load washer 796.4198

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1807405L / P/N MFL68005554 / PDF p.31

Manufacturer document

Use & Care Guide, Kenmore top-load washer 796.2927

Kenmore (guide as published by Sears / Transform SR Brands)

Doc 1007244L / P/N MFL42065471 / PDF p.28

Kenmore 796 front-load washers (guide 1909134L p. 46) and top-load 2927 (guide 1007244L p. 27).

Here to help

Good questions.
Clear answers.

Talk to our team
Is tE on a front-load a reset code?

Yes, in a sense. The guide asks you to unplug the washer, wait 60 seconds, reconnect and try again, and to call if it reappears.

Why does the top-load tE need service?

The 2927 guide calls it a thermistor error, meaning the water temperature sensor is not working correctly, and says to unplug and call.

Is tE a dryer code too?

The 796 dryers use tE1 and tE2 for their own sensor. Those are separate pages.

How long is the unplug wait?

60 seconds.

What should I pass on?

Which layout you have, front-load or top-load, whether the 60-second reset helped, and the model number.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.