What it means
On 796 Kenmore washers, IE signals a slow fill or no fill. Faucets fully open, hoses straight, inlet filters clean and house pressure adequate are the guides' checks. The front-load guide also advises against leak-limiting hoses.
Kenmore washer IE / Water supply
On 796 Kenmore washers, IE signals a slow fill or no fill. Faucets fully open, hoses straight, inlet filters clean and house pressure adequate are the guides' checks. The front-load guide also advises against leak-limiting hoses.
Also shown as IE
On 796 Kenmore washers, IE signals a slow fill or no fill. Faucets fully open, hoses straight, inlet filters clean and house pressure adequate are the guides' checks. The front-load guide also advises against leak-limiting hoses.
A faucet only partly open slows the fill.
IE returns after the supply checks.
Your checklist / stored on this device

A faucet only partly open slows the fill.

Be careful when moving the washer so you do not crush them.

The Care and Cleaning section covers it. Turn off the water first.

See whether household pressure is adequate.

The front-load guide says hoses designed to limit leaks can trip falsely and block the fill.
Give us the model and the checks you have already done, and open your request from here.
Book a visitSimplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Component reference
Each water valve on a Kenmore washer has a small filter screen where the hot and cold hoses connect.
Read the definitionThe guides list the display IE next to the problem washer fills with water slowly or not at all. The causes are all on the supply side.
Read the supporting manualThe front-load guide says they can trip falsely and prevent the washer from filling, and that their use is not recommended.
Read the supporting manualLF is the Calypso Long Fill message with its own clearing key. IE is the 796 equivalent.
Read the supporting manualManufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc 1909134L / P/N MFL68005592 (Transform SR Brands) / PDF p.46
Manufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc 1807405L / P/N MFL68005554 / PDF p.31
Manufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc 1007244L / P/N MFL42065471 / PDF p.27
Covers the 796 front-load (1909134L) and top-load (1007244L) layouts.
It says they can trip falsely and prevent the washer from filling, and that their use is not recommended.
Open another faucet in the house and see whether the flow is strong. The guides ask you to confirm that pressure is adequate and flow is not restricted.
At the washer end of each hose. The Care and Cleaning section shows how to clean them.
They describe the same idea on different families. LF is the Calypso, IE the 796.
When the faucets are open, the hoses straight, the filters clean and IE still returns.
Code, symptom, part or service
LF (Long Fill) tells you a Calypso took too long to fill. Its two questions are whether the inlet hoses are kinked or clogged and whether the inlet valve screens are clear; STOP/CANCEL then clears the display.
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Each water valve on a Kenmore washer has a small filter screen where the hot and cold hoses connect. The guides tie them to slow or no filling: Calypso LF (Long Fill) asks whether the inlet valve screens are clear, and the 796 front-load guide says to clean them if the washer does not fill properly.
Book a diagnostic for your model, carried out at the appliance.
Office details, and the access information to pass along.