Kenmore washer Er / Electronics

Kenmore washer
error Er

Washer / display reference

The Calypso shows Er for a Processor Reset Error: the cycle information was not stored during a power failure. Clear the display with STOP/CANCEL, then set the cycle up again from scratch.

Also shown as Er

Last reviewed

Washer / display reference
Meaning
The Calypso shows Er for a Processor Reset Error: the cycle information was not stored during a power failure. Clear the display with STOP/CANCEL, then set the cycle up again from scratch.
Who handles it
Owner checks first, then a technician
Related codes
Source
Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

What Kenmore washer Er means.

What it means

The Calypso shows Er for a Processor Reset Error: the cycle information was not stored during a power failure. Clear the display with STOP/CANCEL, then set the cycle up again from scratch.

What you can safely check

Press STOP/CANCEL once.

When to call a technician

Er returns on later cycles without a power interruption.

Your checklist / stored on this device

Safe checks, in order.

0 of 5 checks done
  1. Kenmore washer Er: Washers in a thoughtfully designed home
    Illustration. Follow your model’s instructions.
    Before you begin

    Clear the display

    Press STOP/CANCEL once. The guide gives no other step.

  2. A worn rating label on the rim of an older top-load washer
    Illustration. Follow your model’s instructions.
    Check 2

    Think about the power

    Was there a flicker or outage? That is the situation the guide describes.

  3. Over the shoulder of a technician in a navy shirt holding a tablet with a blank checklist, a white washer behind him.
    Illustration. Follow your model’s instructions.
    Check 3

    Choose the cycle again

    The earlier selection is gone, so pick the cycle and options again before you press START.

  4. A technician with a washer drain pump in hand
    Illustration. Follow your model’s instructions.
    Check 4

    Watch the next load

    One Er after a power event is explained. Repeated Er needs a closer look.

  5. Illustration. Follow your model’s instructions.
    Check 5

    Keep the model number

    Calypso models 110.2206, 2408 and 2506 are covered by this list.

Still showing Er?

Give us the model and the checks you have already done, and open your request from here.

Book a visit

The control and its sensors.

Conceptual Washer sectionControl panelControl boardLevel sensorMotor wiring1234
  1. 1Control panel
  2. 4Motor wiring

Simplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

A little more context.

What does Processor Reset Error mean?

The control restarted and could not store where the cycle stood. The guide puts it simply: cycle information was not stored during a power failure.

Read the supporting manual

Is Er the same as PF?

They sit near each other in the list but differ. PF asks whether a power failure interrupted the cycle, and START resumes it. Er says the information was not stored, so you start over.

Read the supporting manual

Does Er mean I need a new control?

The guide does not say. It gives a clearing step and a general call for service if codes continue.

Read the supporting manual

The manual behind the message.

Manufacturer document

Use & Care Guide, Kenmore Calypso washers 110.2206/2408/2506/2508

Kenmore (guide as published by Sears / Transform SR Brands)

Doc L0412465 / P/N 8543703 (Sears, Roebuck and Co.) / PDF p.18

Guide L0412465 prints the Er row on p. 18; it covers the 110.2206, 2408 and 2506.

Here to help

Good questions.
Clear answers.

Talk to our team
Do I lose my wash when Er shows?

The cycle information was not stored, so the cycle must be set up again. Clothes already in the tub stay there, so restart a cycle or rinse and spin.

What is a processor reset?

The control restarted. Er says it lost track of the cycle because power failed before the information could be stored.

Is Er the same as PF?

No. PF asks whether power interrupted the cycle and offers START to continue. Er says the information was not stored, so you start over.

Is one Er worth a service call?

No. After an outage, one Er is expected. If it returns on later cycles without an outage, book a technician.

Does this Er appear on other Kenmore washers?

The Calypso guide prints it. Front-load and top-load 796 washers use other codes.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.