Before work starts
After the technician has examined the appliance you are given the cost of the repair, and you decide whether to go ahead.
Independent appliance repair
We repair Kenmore ranges, wall ovens and cooktops: ovens that will not heat evenly, controls that beep and show an F code, and doors that won’t unlock. Tell us the model number, whether the range is gas or electric, and what the display shows, then book a visit.


On the Kenmore 790 ranges, a dead-looking oven panel usually means one of four things: the oven lockout is on, the clock was never set, an F or E code stopped the control, or power is missing. Cancel the lockout first; a code needs a restart.

A Kenmore oven door that will not open is almost always the self-clean lock, which holds until the oven has cooled. Do not force it. For a door that is misaligned or has been removed, the guide gives hinge-lock steps, and the glass needs care.

On a Kenmore 790 gas cooktop, a flame that is too high, uneven or orange has a short list of causes in the guide: a knob set high, a burner cap sitting wrong, clogged ports, moisture after cleaning or an incorrect LP conversion. Check the cap and ports first.

If a Kenmore 790 gas burner will not light, the guide asks you to push the knob in and turn it fully to Lite, clear the ports, and confirm the range has power. In an outage you can light a burner with a match, carefully.

If self-clean will not start or leaves dirt on a Kenmore 790 oven, the guide points to settings and prep: an active oven lockout, racks left in, a door not fully closed, spills not wiped, or a cooling fan that is not moving air.

Gas odor near a Kenmore range means no flames, no switches. The guide sends you to your gas supplier, using a neighbor's phone, and to the fire department if the supplier cannot be reached. Book a visit only after that.

If a Kenmore 790 oven runs hot, runs cool or bakes unevenly, the guides first look at technique: preheat, rack position and pan spacing. If it still reads wrong, the control can be offset by as much as 35 F in either direction.
No other dishwasher code we have researched is linked to this topic. Compare the exact message with your model manual and do not swap in another code from the library.
See the research statusWe don’t quote parts up front. The technician names any part after the diagnostic and matches it to your exact model number before anything is replaced.
What happens after you book.
Model number first.

Type in the number from the label, along with what the appliance does. A photo of the label works too.

The technician reads the code against your model, finds the failed part and gives you a cost before starting.

The new part goes in, the cycle is tested, and you hear what was done.
The Elite 790.4260 guide says press STOP to clear an F or E code, try bake or broil, and if it repeats turn power off for 5 minutes and repower. The 790.4103 guide says press STOP/CLEAR, reprogram and record the number.
The 790.9375 guide says the control flashes F1, F3 or F9 on a problem. The guides don’t decode these numbers, so the number you record is what the technician needs.
The 790.4260 guide lists a clock that is not set and wrong control settings among the reasons an oven does not operate.
For poor baking the guide lists rack position, preheating, spacing pans, and an Adjusting Oven Temperatures setting.
If you smell gas, do not light anything or touch a switch, don’t use a phone in the building, and call your gas supplier from a neighbor’s phone.
Book a visit if the F code comes back after the 5-minute power-off.
Book a visit if the oven doesn’t heat, the door will not unlock or the controls are dead.
If you smell gas, leave, call your gas supplier from a neighbor’s phone and the fire department if you can’t reach them.
Leave gas and electrical work to the technician; the guide says installation and service must be done by a qualified person.
Arrange a diagnosticAfter the technician has examined the appliance you are given the cost of the repair, and you decide whether to go ahead.
Covered repairs under a Kenmore manufacturer warranty are handled through Kenmore. We stand behind our own work with a workmanship warranty.
The guides we read use F11 only as an example of an F code. They don’t decode it. Clear it with STOP, try bake or broil, and book a visit if it returns.
Yes. Wall ovens and cooktops are booked on this page. Tell us the model number so we bring the right information.
On the Elite ranges the motor-driven latch takes about 15 seconds to move and locks for Self Clean. Wait until Loc leaves the display and don’t force the door.
Not for ranges. The guides only say to clear the code and record it, so our code pages for ranges say that rather than guess a cause.
A repair that falls under the manufacturer’s warranty is handled by the manufacturer. For anything else, book a visit with us and we agree the price before we begin.
Code, symptom, part or service
On the Kenmore 790 ranges, a dead-looking oven panel usually means one of four things: the oven lockout is on, the clock was never set, an F or E code stopped the control, or power is missing. Cancel the lockout first; a code needs a restart.
Kenmore’s Elite 790 ranges lock the oven door with a motor-driven latch. The guide says it locks automatically when you turn on oven lockout (“Loc” shows) and for Self Clean, and warns you not to open or close the door while the latch is moving.
Book a diagnostic for your model, carried out at the appliance.
Office details, and the access information to pass along.