Start from the symptom
Kenmore range burner problems
On a Kenmore 790 gas cooktop, a flame that is too high, uneven or orange has a short list of causes in the guide: a knob set high, a burner cap sitting wrong, clogged ports, moisture after cleaning or an incorrect LP conversion. Check the cap and ports first.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Reseat the burner caps
The cap lip must sit snug and level in the center of the burner head. Slide it gently; it should not move off center and you should hear a click when it seats.
- 2
Flame too high
The guide lists the knob set too high, caps not level and an incorrect LP conversion. Adjust to a lower setting, reseat the caps, and look at the LP kit instructions if the range was converted.
- 3
Uneven flame
With the burner off, clear the ports with a small-gauge wire or needle. After cleaning, a damp burner can burn unevenly; let it run until the flame fills out and dry it fully.
- 4
Orange flame
Dust in the main line makes an orange flame that turns blue after a few minutes. In coastal areas a slightly orange flame can be unavoidable because of salt air.
- 5
Electric cooktops
On the 790.9375 electric range, drip bowls turn color or distort when cookware extends past the element. Match pan size to the element.
Systems a technician may investigate.
We don’t quote parts up front. The technician names any part after the diagnostic and matches it to your exact model number before anything is replaced.
If the display adds a code.
No code is linked directly to this topic.
No other dishwasher code we have researched is linked to this topic. Compare the exact message with your model manual and do not swap in another code from the library.
See the research statusRead the related care guide.

Range panel dead? The oven lockout may be on.
If the touch panel of a Kenmore 790 range seems dead, check the oven lockout first. A Loc message means the door is locked and the keys are off. Hold the lockout key (STOP/CLEAR on some models) for 3 seconds, then wait about 15 seconds. If an F code beeps instead, clear it, reprogram and note the number.

Streaks and burned spills on a glass cooktop? Here is what lifts them.
Clean a Kenmore glass cooktop only when it is cool, with the ceramic-glass cooktop cleaning cream and a non-scratch pad. Remove metal marks soon, scrape burned-on spills with a razor scraper at a shallow angle, and never use bleach, ammonia, oven cleaner or foil. Sugar and plastic are the exception: scrape those at once.
When observation becomes a service request.
Leave internal testing to a technician.
The flame stays tall, yellow-orange or ragged with clean ports and seated caps. Book a visit. A gas smell is a different situation: follow our gas smell page.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore range burner problems guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite slide-in gas range 790.4260/4261
- Use & Care Guide, Kenmore range 790.93750/51/52/54
Go by the instructions for your exact model. Check how we research these pages.
Why is my burner flame so high?
The guide lists a high knob setting, burner caps not seated, and an incorrect LP conversion. Reset the cap and turn the knob down first.
Is an orange flame dangerous?
The guide treats dust in the line and salt air as ordinary causes. If it will not turn blue, book a visit.
How do I clean burner ports?
With the burner off, use a small-gauge wire or needle in each port, per the Care and Cleaning section.
Why is my flame uneven after cleaning?
Moisture. Run the burner until the flame fills out, then dry the heads completely.
Code, symptom, part or service
Link the message to what comes next.
Kenmore range controls not responding
On the Kenmore 790 ranges, a dead-looking oven panel usually means one of four things: the oven lockout is on, the clock was never set, an F or E code stopped the control, or power is missing. Cancel the lockout first; a code needs a restart.
Range repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.
