Start from the symptom
Kenmore washer not draining.
When water stays in a Kenmore washer, the guides start with the drain hose, then the drain pump filter, then the height of the drain. A 796 front-load can also show OE, and a Calypso shows Ld.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Drain hose
Make sure it is not kinked, pinched behind the washer, crushed or clogged. On the 110 front-load, also ask whether the hose is frozen.
- 2
Drain pump filter
On the 796 front-load and top-load, clean the drain pump filter. The guide describes it as the place small objects and lint are caught.
- 3
Drain height
The discharge point may be no more than 96 inches (244 cm) above the bottom of the washer.
- 4
House drain
The Calypso guide says the sink, floor drain or standpipe must take 17 gallons a minute, and that the hose needs an air gap, never taped in. If water backs up, a plumber may be needed.
- 5
Suds
Excess suds slow draining on every family. Use HE detergent and the measured amount.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.
If the display adds a code.
Drain
OE is the 796 Kenmore message for water that drains slowly, or not at all. Inspect the drain hose for kinks and clogs, clean the drain pump filter, and keep the discharge at 96 inches (244 cm) or less above the bottom of the washer. The top-load guide also lists a drain pump that failed.
Drain
Ld (Long Drain) is the Calypso's slow-drain message. The guide asks if the drain hose is kinked or clogged and says STOP/CANCEL clears the display. The 110 front-loaders print F21 and F02 for a drain problem instead.
Read the related care guide.

Washer stops before the spin? Check how it is loaded.
A Kenmore washer stops its spin when the load sits unevenly. Load loosely, mix large and small items, never wash one heavy item alone, and keep the drum from being packed tight. If the washer pauses with an imbalance message, redistribute the load and restart.

Musty front-load washer? Three monthly tasks fix most of it.
Each month, wipe the door seal with the diluted bleach mix, empty the drain pump filter, and leave the door ajar between loads. Check the two inlet filters when the washer fills slowly. All three tasks are in the 796 front-load guide, and each takes only a few minutes.
When observation becomes a service request.
Leave internal testing to a technician.
The hose is clear, the filter is clean and the water level has not dropped. On a 796 top-load the guide lists a failed drain pump as a service item. Book a visit.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore washer not draining guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156
- Use & Care Guide, Kenmore top-load washer 796.2927
- Use & Care Guide, Kenmore Calypso top-load washers 110.2206/2408/2506/2508
- Use & Care Guide, Kenmore front-load washers 110.4708/4709
Go by the instructions for your exact model. Check how we research these pages.
Why is there standing water in my Kenmore washer?
A kinked or clogged drain hose, a clogged drain pump filter, or a drain set higher than 96 inches. Check them in that order.
Where is the drain pump filter?
The 796 front-load keeps it behind a small access panel. The Care and Cleaning section of your guide shows the exact steps.
What does Ld or F21 mean?
Ld (Calypso) is a long drain; F21 (110 front-load) is a drain problem. The guides point to the hose and the drain.
Will the water drain by itself after an error?
On the 796 top-load, an error shown for 4 minutes makes the washer drain the tub on its own, with an alarm one minute before.
Code, symptom, part or service
Link the message to what comes next.
OE
OE is the 796 Kenmore message for water that drains slowly, or not at all. Inspect the drain hose for kinks and clogs, clean the drain pump filter, and keep the discharge at 96 inches (244 cm) or less above the bottom of the washer. The top-load guide also lists a drain pump that failed.
Kenmore washer not spinning
Start with what the display and the lid or door say. A Kenmore washer will not spin until the lid or door is latched, and an out-of-balance load, a slow drain or too many suds can each hold the spin back. Rebalance, check the drain, then book a visit.
Washer drain pump filter
The 796 front-load washer has a drain pump filter behind a small access panel. It catches lint, buttons, keys and coins before they reach the pump. When the washer drains slowly or not at all, the guide’s list starts with the drain hose and then this filter.
Washer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.
