Start from the symptom
Kenmore dryer controls not responding.
If the buttons on a Kenmore dryer do nothing, look for CL in the display: the Control Lock is on. On the 796 dryer, hold TOUCH UP for five seconds. On the Elite HE 110, hold CYCLE SIGNAL for three seconds. A dark drum light is a separate, simpler issue.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Look for CL or the Control Locked light
On the 796 dryer, CL alternates with the time remaining. On the 110, an indicator light glows and you hear a beep when the lock is set.
- 2
Unlock it
796: press and hold TOUCH UP for five seconds. 110: press and hold CYCLE SIGNAL for three seconds until the indicator goes out.
- 3
Power on first
The drum light on the 796 is disabled after the dryer has been off more than four minutes. Press POWER to turn it back on.
- 4
Door and START
If the door does not latch, the control beeps three times. Re-close the door and press START.
- 5
Power failure
PF means the cycle was interrupted. Press and hold START.
Systems a technician may investigate.
We don’t quote parts up front. The technician names any part after the diagnostic and matches it to your exact model number before anything is replaced.

Dryer lint filter
The lint filter is the screen that catches lint before it reaches the exhaust. Kenmore’s dryer guides say to empty it before every load, and the Elite HE guide lists a clogged lint screen first when clothes dry slowly or the load comes out hot. The 796 guide adds a periodic wash.

Dryer exhaust vent
The exhaust vent carries hot, moist air outside. The 796 guide calls poor venting the most common cause of dryer problems, and the Elite HE guide’s AF code means the vent may be crushed or blocked. Both guides say to check the vent run and the outside hood for lint.

Dryer temperature sensor
Kenmore’s 796 dryer guides print one line about the temperature sensor: if the display shows tE1 or tE2, the cause is “Temperature sensor failure,” and the step is to turn off the dryer and get service. They give no owner repair and no reading of what failed.

Dryer moisture sensor
Some Kenmore dryers have a sensor that reads how damp the clothes are. The 796 guide says Auto Dry cycles use it to adjust drying time, and that light items mixed with heavy ones can fool it because the light items dry first. Your own guide says whether your model has one.
If the display adds a code.
Power
PF means power failure: the dryer asks whether its drying cycle was interrupted when power dropped. On the 110 Kenmore dryers, press and hold START to restart. The 8756-series guide adds that you press POWER first.
Not decoded
Kenmore's dryer guides does not print F01. It lists one F-variable service line instead. Check the breakers and the vent, then arrange a visit if the code remains.
Read the related care guide.

Clothes still damp? Feel the air at the outside hood.
Clean the lint screen before every load, run the dryer for 5 to 10 minutes and hold your hand under the outside exhaust hood. No air means the vent is blocked, so clean the run or replace plastic or foil vent with metal. Kenmore guides call poor venting the most common dryer problem.

Dryer stopped at a power cut? Press and hold START, then check two breakers.
After a power cut, a Kenmore dryer may show PF: press and hold START to restart (press POWER first on some models). If the drum turns but there is no heat, check that both household breakers or fuses are on; an electric dryer uses two. L2 points to the home power supply.
When observation becomes a service request.
Leave internal testing to a technician.
The display is blank or ignores presses even with no lock showing and the breaker reset. Book a visit and note which buttons respond.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore dryer controls not responding guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore dryers 796.8128/9128/8118/9118
- Use & Care Guide, Kenmore Elite HE dryer 110.8772
Go by the instructions for your exact model. Check how we research these pages.
Why does my dryer show CL?
Control Lock is on. It is a feature, not an error. Unlock it with the button for your model.
Which button unlocks it?
TOUCH UP for five seconds on the 796, CYCLE SIGNAL for three seconds on the Elite HE 110.
Why is the drum light off?
On the 796, the light is disabled after the dryer has been off more than four minutes. Press POWER.
Does the lock stay on after a power cut?
The guides do not say. If you still see CL or the indicator, use the unlock press.
Code, symptom, part or service
Link the message to what comes next.
PF
PF means power failure: the dryer asks whether its drying cycle was interrupted when power dropped. On the 110 Kenmore dryers, press and hold START to restart. The 8756-series guide adds that you press POWER first.
Kenmore dryer takes too long
Long drying on a Kenmore dryer usually traces back to airflow: a clogged lint screen, a crushed or lint-packed exhaust vent, or a vent run that is too long. The guides give a quick test with your hand under the outside hood.
Dryer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.