Inside the appliance
Dryer exhaust vent. In plain English.
The exhaust vent carries hot, moist air outside. The 796 guide calls poor venting the most common cause of dryer problems, and the Elite HE guide’s AF code means the vent may be crushed or blocked. Both guides say to check the vent run and the outside hood for lint.

Where it fits.
Dryer exhaust vent in the appliance
It runs from the back or side of the dryer to an outside hood. The guides’ installation pages show the standard rear, side and bottom exits for each model.
The picture shows the type of component. It does not pick out a replacement that fits your model.
What you notice when this system needs attention.
Dryer exhaust vent concerns can show up together with weaker performance or a code that keeps returning. Testing is required before deciding whether the component is to blame.

Kenmore dryer takes too long
Long drying on a Kenmore dryer usually traces back to airflow: a clogged lint screen, a crushed or lint-packed exhaust vent, or a vent run that is too long. The guides give a quick test with your hand under the outside hood.

Kenmore dryer temperature problems
A Kenmore dryer that runs too hot, too cool or without heat is covered by three kinds of check in the guides: airflow, the household power supply, and a sensor message. Clear the lint and vent first, then check breakers and the gas valve on gas models.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Look at the run
The Elite HE guide’s AF steps: check that the vent between the dryer and the wall is not crushed, and that the run and the outside hood are free of lint and debris.
- 2
Check length and bends
The guide says the vent has to stay within the recommended length and number of elbows for its type. Use heavy metal vent, not plastic or metal foil, which the guide labels a fire hazard.
- 3
Feel the airflow
The Elite HE guide describes running the dryer for a few minutes and holding a hand under the outside hood. If you feel no air, clean the exhaust system or replace the vent with heavy metal or flexible metal vent.
- 4
Clean it yearly
The 796 guide says vent ducts should be checked for lint buildup and cleaned at least once a year, and sooner if drying slows.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if AF returns, or if the 796 dryer’s Check Vent light comes on, after the vent run and hood are clear.
Book a visit if the vent is crushed or damaged and you want it checked on site.
Stop using the dryer if you find a plastic or foil vent; the guide calls it a fire hazard.
Arrange a diagnosticSources and model boundaries.
These sources back up the Dryer exhaust vent guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite HE dryer 110.8772
- Use & Care Guide, Kenmore dryers 796.8128/9128/8118/9118
Go by the instructions for your exact model. Check how we research these pages.
What does AF mean on a Kenmore dryer?
On the 110 Elite HE dryer, AF means the vent may be crushed or blocked. Check the run to the wall, the duct and the outside hood for lint, then restart on Timed Dry.
What does the Check Vent light mean?
On the 796 dryers it signals a serious drop in exhaust airflow. The dryer keeps running, but the guide says to have the exhaust system cleaned or repaired right away.
Does the warranty cover a blocked vent?
The 796 guide says damage from damaged, restricted or inadequate exhaust systems is not covered by the dryer warranty. Check your own warranty terms for details.
What vent material should I use?
The Elite HE guide says to use heavy metal vent. It warns against plastic and metal foil vent and lists a fire hazard if you don’t follow it.
Code, symptom, part or service
Link the message to what comes next.
Kenmore dryer takes too long
Long drying on a Kenmore dryer usually traces back to airflow: a clogged lint screen, a crushed or lint-packed exhaust vent, or a vent run that is too long. The guides give a quick test with your hand under the outside hood.
Dryer lint filter
The lint filter is the screen that catches lint before it reaches the exhaust. Kenmore’s dryer guides say to empty it before every load, and the Elite HE guide lists a clogged lint screen first when clothes dry slowly or the load comes out hot. The 796 guide adds a periodic wash.
Dryer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.

