Start from the symptom
Kenmore dryer temperature problems.
A Kenmore dryer that runs too hot, too cool or without heat is covered by three kinds of check in the guides: airflow, the household power supply, and a sensor message. Clear the lint and vent first, then check breakers and the gas valve on gas models.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Lint screen and vent for a hot load
The 110 guide lists "load is too hot" together with slow drying and ties both to the lint screen and exhaust vent. Clean the screen and check the hood airflow.
- 2
Vent material
The guide's Fire Hazard box says to use a heavy metal vent, not plastic and not metal foil. If yours is foil or plastic, book a visit to discuss the vent.
- 3
No heat on an electric dryer
Electric dryers use two fuses or breakers. The drum can turn with one tripped, so check both. L2 on the Elite HE 110 points the same way.
- 4
No heat on a gas dryer
The 796 guide says to confirm that the house gas shutoff and the dryer's own valve are both fully open. The dryer will run with no gas and show no code.
- 5
Read a tE1 or tE2 message
On the 796 models these mean a temperature sensor failure. The guide says to turn off the dryer and arrange service.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.

Dryer temperature sensor
Kenmore’s 796 dryer guides print one line about the temperature sensor: if the display shows tE1 or tE2, the cause is “Temperature sensor failure,” and the step is to turn off the dryer and get service. They give no owner repair and no reading of what failed.

Dryer exhaust vent
The exhaust vent carries hot, moist air outside. The 796 guide calls poor venting the most common cause of dryer problems, and the Elite HE guide’s AF code means the vent may be crushed or blocked. Both guides say to check the vent run and the outside hood for lint.

Dryer lint filter
The lint filter is the screen that catches lint before it reaches the exhaust. Kenmore’s dryer guides say to empty it before every load, and the Elite HE guide lists a clogged lint screen first when clothes dry slowly or the load comes out hot. The 796 guide adds a periodic wash.
If the display adds a code.
Temperature
tE1 on Kenmore 796 dryers (the 8128 family and the 8138 steam dryers) is listed as a temperature sensor failure. The guide's remedy is to switch the dryer off and request service, so stop drying and book a technician.
Temperature
tE2 on Kenmore 796 dryers is printed in the same row as tE1: temperature sensor failure. Kenmore answers with a power-down and a service request. No reset is given and no home repair is described, so book a technician.
Power
L2 on the Kenmore Elite HE 110.8772 means the drum turns but a power-supply problem at home may be keeping the heater from starting. Check the pair of fuses or breakers that feed an electric dryer, and call in an electrician if L2 persists.
Airflow
AF on a Kenmore Elite HE 110.8772 dryer says the vent may be crushed or blocked. Run the dryer for 5 to 10 minutes and hold your hand under the outside hood. No air means clean the exhaust system or replace the vent with heavy or flexible metal vent.
Read the related care guide.

Clothes still damp? Feel the air at the outside hood.
Clean the lint screen before every load, run the dryer for 5 to 10 minutes and hold your hand under the outside exhaust hood. No air means the vent is blocked, so clean the run or replace plastic or foil vent with metal. Kenmore guides call poor venting the most common dryer problem.

Dryer stopped at a power cut? Press and hold START, then check two breakers.
After a power cut, a Kenmore dryer may show PF: press and hold START to restart (press POWER first on some models). If the drum turns but there is no heat, check that both household breakers or fuses are on; an electric dryer uses two. L2 points to the home power supply.
When observation becomes a service request.
Leave internal testing to a technician.
There is still no heat after the breakers are reset, or tE1 or tE2 shows. Book a visit. Smell gas? Leave the house and call the gas supplier before anything else.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore dryer temperature problems guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite HE dryer 110.8772
- Use & Care Guide, Kenmore dryers 796.8128/9128/8118/9118
Go by the instructions for your exact model. Check how we research these pages.
Why does my dryer run but not heat?
Electric models: a tripped breaker or blown fuse is the first suspect, because the drum still tumbles. Gas models: confirm both gas valves are fully open.
Why are my clothes too hot to touch?
The 110 guide groups a hot load with long dry times and points to the lint screen and exhaust vent. Restricted airflow is the lead check.
What does tE1 or tE2 mean?
A temperature sensor failure on 796 dryers. Turn the dryer off and book a visit.
What vent should I use?
Heavy metal or flexible metal. The guide warns against plastic and metal-foil vents because of fire risk.
Code, symptom, part or service
Link the message to what comes next.
tE1
tE1 on Kenmore 796 dryers (the 8128 family and the 8138 steam dryers) is listed as a temperature sensor failure. The guide's remedy is to switch the dryer off and request service, so stop drying and book a technician.
Kenmore dryer takes too long
Long drying on a Kenmore dryer usually traces back to airflow: a clogged lint screen, a crushed or lint-packed exhaust vent, or a vent run that is too long. The guides give a quick test with your hand under the outside hood.
Dryer lint filter
The lint filter is the screen that catches lint before it reaches the exhaust. Kenmore’s dryer guides say to empty it before every load, and the Elite HE guide lists a clogged lint screen first when clothes dry slowly or the load comes out hot. The 796 guide adds a periodic wash.
Dryer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.