On this page
- PF means the cycle was interrupted by a power failure. 12
- Electric dryers use two fuses or breakers; check both. 12
- L2 on the Elite HE: drum turns, but the home supply may be stopping the heater. 1
- Use a time-delay fuse and never a bigger one. 13
- A paused 110 Elite cycle shuts off after 5 minutes; a 796 one after four. 13
Why does my Kenmore dryer show PF after a power cut?#
PF means power failure. The dryer is telling you that the drying cycle was interrupted when power dropped. On the Kenmore Elite HE guide you press and hold START to restart it. On the 110.8756 series you press POWER first, then hold START. 12
That is all the guides say about PF, and it is all it means. It shows on the display in place of the time, which is why people read it as a breakdown when it is only a pause. The dryer has not been damaged by the outage. Our PF page has the code on its own, and this guide covers what else to check when the dryer does not come back to life.
Plan on restarting the cycle from where it stopped. The Elite HE guide says drying continues if you close the door and press START within 5 minutes, and that the dryer shuts off if the cycle is interrupted for longer. On the 796 dryers the limit is four minutes after a pause. 13
- 1
- 2
- 3
- 4
If PF will not clear#
A PF message that comes back every time you restart is worth a closer look at the supply. If the dryer will not restart, work through the "dryer will not run" list in the guide: the fuses or breakers, the power supply, the fuse type, the door and the START button. The next section covers those. 12
Why do electric dryers have two breakers?#
An electric dryer runs on a 240-volt supply, which comes through two household fuses or breakers. If either one trips, the dryer may stop, or the drum may turn with no heat. The guides say to check that both are intact and reset. 12
The Elite HE guide puts it this way: there may be 2 fuses or circuit breakers for the dryer, so check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse or reset the breaker. If the problem continues, call an electrician. 1
What the other checks say#
The "dryer will not run" list in the guides has five more items beyond the breakers. None needs a tool, and all of them are quick to rule out before you decide the dryer itself has a problem. 123
- Power supply. Electric dryers require a 240-volt supply. Check with a qualified electrician. 1
- Fuse type. Use a time-delay fuse, not a regular one. 12
- Do not raise the fuse size. The 796 guide says not to increase fuse capacity, and to have a circuit overload corrected by a qualified electrician. 3
- Door. If the top of the door does not latch when you push START, the control beeps 3 times. Open the door, close it firmly and start again. 1
- Cord. The 796 guide says to make sure the plug is securely in a grounded outlet matching the dryer's rating plate. 3
Why no heat can look like a working dryer#
The 796 guide says that, due to the design of electric dryers, a circuit problem can let an electric dryer run without heat. A turning drum does not mean both legs are live. 3
Gas models are different: if the house gas shutoff or the dryer's gas shutoff is not fully open, the dryer will run and no error code shows. Confirm both are open and that other gas appliances work. 3
What does L2 mean on a Kenmore Elite HE dryer?#
On the Elite HE 110.8772, L2 means the drum will turn, but there may be a problem with your home power supply keeping the dryer's heater from turning on. Check for a blown household fuse or a tripped circuit breaker, reset it or replace the fuse, and call an electrician if it continues. 1
The guide says to select a Timed Dry heated cycle and restart the dryer. If the message persists, consult a qualified electrician. The dryer continues to run while L2 shows, and pressing any key clears it from the display, bringing back the Estimated Time Remaining. 1
Our L2 page states the code by itself.
Where L2 does not apply#
L2 is printed in the Elite HE guide. The 110.8756-series and 796 guides we read do not print it, so do not assume it means the same elsewhere. On those, the same advice applies to a dryer that runs without heat: check both breakers. 23

What if the dryer still has no heat or a code stays on?#
Run a Timed Dry heated cycle after the breakers are reset. If the drum turns with no heat, or L2 comes back, the home supply or the dryer needs a closer look. An F code (F1, F2, F20) or an E code on the 8756 series means call for service. 12
The guides do not decode those F and E codes. Write down the exact characters. Our page on dryer codes without a printed meaning covers what the guides say and do not say.
Before you call#
A few notes make the visit shorter and help an electrician too. Note whether both breakers are on, whether anything else in the house lost power or acts oddly, and whether the dryer ran normally before the outage. If lights flicker or other appliances trip the same circuit, tell the electrician.
When should I book a technician?#
Book a visit if L2 or no heat continues after both breakers or fuses are on and the dryer has run a heated Timed Dry cycle, or if an E or F code remains. If a breaker trips again and again, an electrician comes first. 123
You can book a visit, read about our dryer service or see the dryer temperature problems page. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. If your unit is under the manufacturer's warranty, the manufacturer handles that repair. We give a warranty on our workmanship.
Sources#
- Use & Care Guide, Kenmore Elite HE electric dryer 110.8772Kenmore / Sears Roebuck · Document L0708325 (part W10136973A), no date printed · pp. 21 (Dryer Use, pause and restart), 28 (Troubleshooting: PF, L2, F codes, will not run, no heat)
- Use & Care Guide, Kenmore electric dryers 110.8756/8757/8758/8856/8857/8858Kenmore / Sears Roebuck · Document 1506245L (part W10035050C), no date printed · p. 27 (Troubleshooting: will not run, no heat, PF, E codes)
- Use & Care Guide, Kenmore dryers 796.8128/9128/8118/9118Kenmore / Sears Brands · Document 1901122L (part MFL67731010), no date printed · pp. 19 (Operating the Dryer, pause), 29-30 (Troubleshooting: will not turn on, does not heat)


