What it means
tE1 on Kenmore 796 dryers (the 8128 family and the 8138 steam dryers) is listed as a temperature sensor failure. The guide's remedy is to switch the dryer off and request service, so stop drying and book a technician.
Kenmore dryer tE1 / Temperature
tE1 on Kenmore 796 dryers (the 8128 family and the 8138 steam dryers) is listed as a temperature sensor failure. The guide's remedy is to switch the dryer off and request service, so stop drying and book a technician.
Also shown as tE1
tE1 on Kenmore 796 dryers (the 8128 family and the 8138 steam dryers) is listed as a temperature sensor failure. The guide's remedy is to switch the dryer off and request service, so stop drying and book a technician.
Stop the cycle and turn the dryer off.
tE1 is on the display, whatever the load.
Your checklist / stored on this device

Stop the cycle and turn the dryer off. The guide gives this as its first and only step.

Open the door once the drum has cooled and take out the laundry so nothing sits warm in the drum.

The guide does not list this, but a clogged screen or vent is worth clearing before the technician arrives.

Look for 796 on the rating label. Only the 796 laundry guides print a tE1 row.
Give the technician the model number and tell them tE1 appeared on the display.
Give us the model and the checks you have already done, and open your request from here.
Book a visitSimplified drawing; the real layout depends on the model. Tap an outlined part to see its photo and the check that goes with it.

Component reference
Kenmore’s 796 dryer guides print one line about the temperature sensor: if the display shows tE1 or tE2, the cause is “Temperature sensor failure,” and the step is to turn off the dryer and get service.
Read the definitionIn the Before Calling table, a display showing tE1 or tE2 is paired with temperature sensor failure and a request to power down and call.
Read the supporting manualIn general terms it reports drying-air temperature back to the control. A failed sensor leaves the control without that reading. The guide stops at naming the failure.
Read the supporting manualNo. A washer tE is on the front-load washer table and means something else. Look up the washer page if your appliance is a washer.
Read the supporting manualManufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc 1901122L / P/N MFL67731010 / PDF p.31
Manufacturer document
Kenmore (guide as published by Sears / Transform SR Brands)
Doc 1405214L / P/N MFL67731025 (Sears Brands) / PDF p.33
Two 796 guides: 1901122L p. 31 for the 8128 family, and 1405214L p. 33 for the 8138 and 9138 steam models.
The troubleshooting row pairs tE1 with temperature sensor failure and gives one instruction, to turn off the dryer and call for service. We read that as a reason not to keep running heat cycles.
The guide names the temperature sensor, not the heater. The sensor reports air temperature to the control, so the heating parts may be fine.
The 796 dryers in the 8128, 9128, 8118 and 9118 guide and the steam 8138 and 9138 guide. Other families, such as the 110 dryers, print different codes.
Kenmore's 796 front-load washers print tE as a control error and the top-load as a thermistor error. Those are separate pages, so do not mix the dryer and washer steps.
Cleaning it is good practice, but the guide lists lint on clothes as a separate problem. tE1 still needs service even with a clean screen.
Code, symptom, part or service
tE2 on Kenmore 796 dryers is printed in the same row as tE1: temperature sensor failure. Kenmore answers with a power-down and a service request. No reset is given and no home repair is described, so book a technician.
Long drying on a Kenmore dryer usually traces back to airflow: a clogged lint screen, a crushed or lint-packed exhaust vent, or a vent run that is too long. The guides give a quick test with your hand under the outside hood.
Kenmore’s 796 dryer guides print one line about the temperature sensor: if the display shows tE1 or tE2, the cause is “Temperature sensor failure,” and the step is to turn off the dryer and get service. They give no owner repair and no reading of what failed.
Book a diagnostic for your model, carried out at the appliance.
Office details, and the access information to pass along.