Start from the symptom
Kenmore ice maker not making ice.
For a Kenmore bottom-freezer ice maker that makes nothing, the guide lists a fresh install, the power switch, a dirty ice sensor, no water supply, a blocked shut-off arm or sensor, and reverse osmosis pressure. A new unit can take 12 to 24 hours to make ice.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
New install: wait
It may take up to 24 hours for each compartment to reach temperature and for the ice maker to start. Wait 72 hours for full ice production.
- 2
Switch the ice maker on
Find the ON/OFF switch and confirm it sits at ON (I).
- 3
Clean the ice sensor
Foreign substances or frost on the ice-detecting sensor can interrupt ice production. Keep the sensor area clean.
- 4
Check the water supply
Connect the refrigerator to water and turn the shutoff valve fully open.
- 5
Free the shut-off arm
With an arm, make sure it moves freely. With the electronic sensor, keep a clear path between the two sensors.
- 6
Level the ice in the bin
Uneven ice can make the icemaker misread the amount and stop. Shake the bin to level it, and keep the ice door closed tightly.
- 7
Think about reverse osmosis
An RO system can drop water pressure below the minimum and cause ice maker problems.
More about this symptom.
What does Kenmore list for no ice?#
A recent install or connection, the ice maker off, a blocked sensor, no water or a closed shutoff, an obstructed arm or sensor, and a reverse osmosis system.
How does the ice maker know the bin is full?#
With a shut-off arm or an electronic sensor. When the bin fills to the arm, ice making stops. Nothing should interfere with the sweep of the arm.
If the symptom returns, what then?#
When the switch, sensor, arm, supply and time after installation are all in order and no ice appears. The water inlet valve or ice maker module needs testing then.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.

Ice maker shut-off arm and ice sensor
The shut-off arm or electronic ice sensor tells the Kenmore ice maker when the bin is full. The 795 guide says to make sure the arm moves freely, or that there is a clear path between the two sensors. Frost on the ice-detecting sensor can also interrupt ice production.

Refrigerator ice maker
The automatic ice maker takes in water, freezes it into cubes and sends them to the bin. The Kenmore 795 guide says a new refrigerator takes 12 to 24 hours to start making ice and 72 hours to reach full output, and lists the switch, the ice sensor, the shut-off arm and the water supply as the usual checks.

Refrigerator water filter
This cartridge treats the water on its way to the dispenser and the ice maker. Kenmore’s refrigerator guides say to replace it about every six months, when the indicator comes on, when dispenser output drops or when the ice cubes get smaller than normal.
If the display adds a code.
Keep the exact message.
We have not researched code meanings for this appliance. Use its model manual, and attach a photo of the display to your request.
See the research statusWhen observation becomes a service request.
Leave internal testing to a technician.
Still no ice after 72 hours on a new install.
The arm moves freely, the sensor is clean and the supply valve is open, but no ice appears.
The ice maker buzzes with no water connected.
Ice is discolored.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore ice maker not making ice guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite bottom-freezer refrigerator 795.7802/7804/7902/7904
- Use & Care Guide, Kenmore bottom-freezer refrigerator 795.7248
Go by the instructions for your exact model. Check how we research these pages.
How long before a new Kenmore ice maker makes ice?
About 12 to 24 hours to begin, and the guide says to wait 72 hours for full ice production. Throw away the first few batches, which can carry particles or odor from the supply line.
How much water pressure does the ice maker need?
The 795.7802 guide says 20 to 120 psi on models without a water filter and 40 to 120 psi on models with a water filter, to produce the normal amount and size of cubes.
Why did the ice maker stop with an empty bin?
The ice-detecting sensor or shut-off arm may be obstructed. Frost or foreign substances on the sensor can interrupt ice production. Empty the bin, free the arm and reinstall it.
Can the ice door cause no ice?
Yes, in the 795.7248 guide. If the ice compartment door is not closed tightly, the cold air can freeze food in the refrigerator and the ice maker may stop producing ice.
Is it OK to leave the ice maker on with no water?
No. The guide says keeping the power switch ON before the water line is connected can damage the ice maker, and the valve buzzes. Leave it at OFF until the line is hooked up.
Code, symptom, part or service
Link the message to what comes next.
Kenmore ice maker not making ice
For a Kenmore bottom-freezer ice maker that makes nothing, the guide lists a fresh install, the power switch, a dirty ice sensor, no water supply, a blocked shut-off arm or sensor, and reverse osmosis pressure. A new unit can take 12 to 24 hours to make ice.
Refrigerator ice maker
The automatic ice maker takes in water, freezes it into cubes and sends them to the bin. The Kenmore 795 guide says a new refrigerator takes 12 to 24 hours to start making ice and 72 hours to reach full output, and lists the switch, the ice sensor, the shut-off arm and the water supply as the usual checks.
Ice maker repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.