Start from the symptom
Kenmore cooktop Elite gas cooktop: burner stays dark.
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Smell for gas first
With a gas smell, light nothing and touch no switch. Get out and reach the gas company by phone from outside.
- 2
Turn the knob to LITE
Push in and turn the surface control knob to LITE until the burner ignites, then turn to the flame size you want.
- 3
Check the gas supply valve
Check that the gas line valve is open.
- 4
Seat the burner
The gas-air mixture needs a straight line to travel. On open burner models, check the burner sits properly in its support.
- 5
Clean the ports
Using a thin wire or needle, with the burner off, work the ports or slots clear.
- 6
Check the cord
On electric ignition models, make sure the power cord is plugged securely into the outlet.
- 7
In an outage, light by hand
Electric ignition burners can be lit manually. Follow Setting Surface Controls in your guide.
More about this symptom.
What does the guide say about the knob?#
Push in and turn the surface control knob to LITE until the burner ignites. The burner will not light if the knob was not turned completely to LITE.
What about a flame that burns half way around?#
Clogged ports or slots, or moisture after cleaning. Clear the ports using a thin wire or needle while the burner is off, or lightly fan the flame and let it run until it is full.
What do two guide editions say?#
Both gas cooktop guides list the same causes and fixes for burners that do not light, a half-way flame and an orange flame.
Systems a technician may investigate.
These parts are linked to the symptom. Noticing the symptom does not show that any single part has failed.

Gas cooktop surface burners
Each burner on a Kenmore gas cooktop has a head and a cap. The guide wants the cap level and centered, and that spills or cleaner in the gas orifice opening stop proper ignition. Clogged ports cause burners that will not light or burn only half way around; the fix is to clean them with the burner off.

Gas cooktop electronic igniter
Electric-ignition Kenmore gas cooktops spark all the ignitors at once when you turn any knob to LITE, but only the burner you chose lights. The guide says push in and turn the knob until the burner ignites, then set the flame, and not to cook with the knob left at LITE. In a power outage burners can be lit with a match.
If the display adds a code.
Keep the exact message.
We have not researched code meanings for this appliance. Use its model manual, and attach a photo of the display to your request.
See the research statusWhen observation becomes a service request.
Leave internal testing to a technician.
You smell gas.
The flame burns only part way around the burner after cleaning.
The flame stays orange after several minutes.
The burner does not light and the ports are clear.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore Elite gas cooktop: burner stays dark guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite gas cooktop 790.32703, 790.32713
- Use & Care Guide, Kenmore Elite gas cooktop 790.3244, 3245, 3248, 3249
Go by the instructions for your exact model. Check how we research these pages.
Why will my Kenmore gas cooktop burner not light?
The guide lists the knob not turned fully to LITE, a closed gas supply valve, a burner not seated straight, clogged ports or slots, a disconnected cord on electric ignition models, and a power outage.
How do I clean clogged burner ports?
Take a thin wire or needle, with the burner off, and clear the ports or slots. Dry the burner thoroughly after cleaning, since moisture can make the flame burn only half way around.
Why is my flame orange or uneven?
Dust in the gas line can make it orange for a few minutes until it turns blue. In coastal areas a slightly orange flame is unavoidable due to salt air. A flame half way around points to clogged ports or moisture.
Can burners be lit by hand in an outage?
On electric ignition models the burners can be lit manually. Use the Setting Surface Controls section of the guide, and keep sleeves and hair away from the flame.
What should I write down before the visit?
When the knob, gas valve, burner seat, ports and power are right and the burner still will not light. Gas parts are not for owners to adjust. If you smell gas, leave first.
Code, symptom, part or service
Link the message to what comes next.
Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.
Gas cooktop surface burners
Each burner on a Kenmore gas cooktop has a head and a cap. The guide wants the cap level and centered, and that spills or cleaner in the gas orifice opening stop proper ignition. Clogged ports cause burners that will not light or burn only half way around; the fix is to clean them with the burner off.
Cooktop repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.