Inside the appliance
Gas cooktop electronic igniter. In plain English.
Electric-ignition Kenmore gas cooktops spark all the ignitors at once when you turn any knob to LITE, but only the burner you chose lights. The guide says push in and turn the knob until the burner ignites, then set the flame, and not to cook with the knob left at LITE. In a power outage burners can be lit with a match.

Where it fits.
Gas cooktop electronic igniter in the appliance
The ignitors are electronic, one per burner. The guide shows no diagram of them; they spark at the burner when any knob is set to LITE.
The picture shows the type of component. It does not pick out a replacement that fits your model.
What you notice when this system needs attention.
Gas cooktop electronic igniter concerns can show up together with weaker performance or a code that keeps returning. Testing is required before deciding whether the component is to blame.

Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.

Kenmore radiant cooktop element not heating
For a Kenmore radiant cooktop, the guide names a blown fuse or breaker trip, an outage, a heat setting too low, the wrong control for the element, incorrect voltage, and lightweight or warped pans. Raise the setting a little and use flat, medium or heavy cookware.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Go all the way to LITE
The guide wants the knob all the way at LITE. Push in and turn until the burner ignites, then turn to the flame size.
- 2
Check the plug and power
Electric ignition models need the cord seated in the outlet, and an outage stops sparking.
- 3
Light by hand in an outage
Hold a lit match to the burner head, then slowly turn the knob to LITE. Use caution.
- 4
Do not leave it in LITE
The electronic ignitor keeps sparking while the knob is in LITE, so move it to a flame setting once the burner is lit.
Cleaning or replacement?
Leave internal testing to a technician.
If you smell gas, leave the area first, then book a visit.
Book a visit if one burner never sparks while the others do.
Book a visit if the clicking never stops, or burners spark but will not catch with ports clean and caps seated.
Arrange a diagnosticSources and model boundaries.
These sources back up the Gas cooktop electronic igniter guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore gas cooktop 790.32703, 790.32713
Go by the instructions for your exact model. Check how we research these pages.
Why do all burners click?
The guide says when any knob is set to LITE all electronic surface ignitors spark together, though only the burner you are setting ignites.
What if the power is out?
The burners can be lit manually. Hold a lit match to the burner head and slowly turn the control knob to LITE.
Why does it keep clicking?
If the knob remains in LITE the ignitor keeps sparking. The guide says not to cook in that position.
When is the cord a cause?
On electric ignition models, a power cord out of the outlet stops the burners from lighting, the guide says.
Code, symptom, part or service
Link the message to what comes next.
Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.
Cooktop repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.

