Inside the appliance
Radiant cooktop surface element. In plain English.
Kenmore ceramic glass cooktops heat with radiant elements under the glass. The guide says each element gives constant heat at each setting, a glowing red area beyond the pot means the cookware is too small, and the hot surface indicator stays lit until the cooktop has cooled. Dual elements have SINGLE and DOUBLE markings.

Where it fits.
Radiant cooktop surface element in the appliance
Under the ceramic glass at the marked cooking zones: two single elements on a 30-inch model, three on a 36-inch, with dual elements at the left and right front.
The picture shows the type of component. It does not pick out a replacement that fits your model.
What you notice when this system needs attention.
Radiant cooktop surface element concerns can show up together with weaker performance or a code that keeps returning. Testing is required before deciding whether the component is to blame.

Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.

Kenmore radiant cooktop element not heating
For a Kenmore radiant cooktop, the guide names a blown fuse or breaker trip, an outage, a heat setting too low, the wrong control for the element, incorrect voltage, and lightweight or warped pans. Raise the setting a little and use flat, medium or heavy cookware.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Check the setting and the knob
If an element does not heat, raise the setting slightly and be sure you turned the control for that element.
- 2
Check the whole cooktop
If nothing works, look for a blown fuse or tripped breaker, wiring that is not complete, or a power outage.
- 3
Check the cookware
Use flat-bottom, evenly balanced medium or heavy pans. Lightweight or warped pans heat unevenly and burn food.
- 4
Use the dual element correctly
Turn counterclockwise for the inner coil only and clockwise for both coils.
Cleaning or replacement?
Leave internal testing to a technician.
Book a visit if an element stays cold with power confirmed and the right control on.
Book a visit if an element stays on or too hot when the knob is off or low.
Book a visit when the glass is cracked, or the indicator stays lit long after the cooktop has cooled.
Arrange a diagnosticSources and model boundaries.
These sources back up the Radiant cooktop surface element guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore radiant electric cooktop 790.4511, 790.4512
Go by the instructions for your exact model. Check how we research these pages.
Why does the hot surface light stay on?
The guide says the indicator stays lit while the glass is still hot enough to burn, even with the controls off.
What does glowing red beyond the pot mean?
The guide says a glowing red heating area extending beyond the bottom edge of the cookware means the cookware is too small for the element.
Why is an element not heating?
The guide lists no power to the appliance, too low a setting, or the wrong control being on. Check the fuse or breaker first.
Why is food heating unevenly?
Lightweight or warped pans, or the wrong setting. Heavy and medium-weight flat pans heat evenly.
Code, symptom, part or service
Link the message to what comes next.
Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.
Cooktop repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.

