Inside the appliance
Gas cooktop surface burners. In plain English.
Each burner on a Kenmore gas cooktop has a head and a cap. The guide wants the cap level and centered, and that spills or cleaner in the gas orifice opening stop proper ignition. Clogged ports cause burners that will not light or burn only half way around; the fix is to clean them with the burner off.

Where it fits.
Gas cooktop surface burners in the appliance
On top of the cooktop. Each burner has a head with a cap resting on it, and the grates sit over them.
The picture shows the type of component. It does not pick out a replacement that fits your model.
What you notice when this system needs attention.
Gas cooktop surface burners concerns can show up together with weaker performance or a code that keeps returning. Testing is required before deciding whether the component is to blame.

Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.

Kenmore radiant cooktop element not heating
For a Kenmore radiant cooktop, the guide names a blown fuse or breaker trip, an outage, a heat setting too low, the wrong control for the element, incorrect voltage, and lightweight or warped pans. Raise the setting a little and use flat, medium or heavy cookware.
Owner care, within the model instructions.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Check the cap
Slide the cap gently side to side. The cap lip should fit snug into the center of the burner head and not move off center.
- 2
Clean the ports
With the burner off, poke the ports or slots clear with a small-gauge wire or needle. Dry the burners thoroughly after washing.
- 3
Fan a wet burner
If the flame burns half way around after cleaning, lightly fan the flame and let the burner run until the flame is full.
- 4
Read the color
A steady blue flame is right. An orange flame may be dust in the gas line, or salt air in coastal areas, per the guide.
Cleaning or replacement?
Leave internal testing to a technician.
If you smell gas, get out and call the gas utility from outside, then book a visit.
Book a visit if a clean, dry burner with the cap seated still will not light or stays uneven.
Book a visit if the flame is yellow or lifts off the burner after cleaning.
Arrange a diagnosticSources and model boundaries.
These sources back up the Gas cooktop surface burners guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore gas cooktop 790.32703, 790.32713
- Use & Care Guide, Kenmore Elite gas cooktop 790.3244, 3245, 3248, 3249
Go by the instructions for your exact model. Check how we research these pages.
Why will my burner not light?
The guide lists a control knob not fully turned to LITE, a closed gas valve, a burner not seated, clogged ports, or a disconnected cord on electric ignition models.
Why does the flame burn on only half the burner?
Clogged ports or moisture after cleaning, the guide says. Clean the ports and fan the flame until it is full.
Why is my flame orange?
Dust in the main line, which clears in a few minutes, or salt air in coastal areas where a slightly orange flame is unavoidable.
Is the burner cap important?
Yes. The guide says to use no burner without all caps properly installed, to avoid flare-ups and harmful by-products.
Code, symptom, part or service
Link the message to what comes next.
Kenmore Elite gas cooktop: burner stays dark
If a Kenmore Elite gas burner stays dark, push in the knob and rotate fully to LITE until it ignites, then set the flame. After that, confirm the gas valve is open, the burner sits straight in its support, the ports are clear and, on electric ignition models, the cord is in.
Cooktop repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.

