Start from the symptom
Kenmore dryer drum not turning.
The Kenmore dryer guides do not describe a mechanical cause for a drum that will not turn, so we stay with what they print: a dryer that will not run needs power, a firmly closed door and a firm START press. Large loads may need START held 2 to 5 seconds.

Start with safe observations.
Switch the appliance off and unplug it before any owner check. Be careful around standing water and sharp debris. Never touch a wet plug or electrical area, take off service panels, or go past what your model’s owner instructions allow.
- 1
Door latch
If the top of the door does not latch when you push START, the control beeps three times. Open the door, close it firmly and start again.
- 2
Press and hold START
The Elite HE 110 guide says large loads may require pressing START for 2 to 5 seconds.
- 3
Fuses and breakers
Electric dryers have two. Check that both are intact and tight, or that neither breaker has tripped. The guide also says electric dryers need 240-volt power and a time-delay fuse.
- 4
Check for a snag
A coin, button or paper clip caught between the drum and the front or rear panel is listed under unusual sounds. Look at the drum edges.
- 5
PF in the display
A power failure interrupted the cycle. Press and hold START to restart the dryer.
Systems a technician may investigate.
We don’t quote parts up front. The technician names any part after the diagnostic and matches it to your exact model number before anything is replaced.

Dryer lint filter
The lint filter is the screen that catches lint before it reaches the exhaust. Kenmore’s dryer guides say to empty it before every load, and the Elite HE guide lists a clogged lint screen first when clothes dry slowly or the load comes out hot. The 796 guide adds a periodic wash.

Dryer exhaust vent
The exhaust vent carries hot, moist air outside. The 796 guide calls poor venting the most common cause of dryer problems, and the Elite HE guide’s AF code means the vent may be crushed or blocked. Both guides say to check the vent run and the outside hood for lint.

Dryer temperature sensor
Kenmore’s 796 dryer guides print one line about the temperature sensor: if the display shows tE1 or tE2, the cause is “Temperature sensor failure,” and the step is to turn off the dryer and get service. They give no owner repair and no reading of what failed.

Dryer moisture sensor
Some Kenmore dryers have a sensor that reads how damp the clothes are. The 796 guide says Auto Dry cycles use it to adjust drying time, and that light items mixed with heavy ones can fool it because the light items dry first. Your own guide says whether your model has one.
If the display adds a code.
Power
PF means power failure: the dryer asks whether its drying cycle was interrupted when power dropped. On the 110 Kenmore dryers, press and hold START to restart. The 8756-series guide adds that you press POWER first.
Not decoded
Kenmore's dryer guides does not print F01. It lists one F-variable service line instead. Check the breakers and the vent, then arrange a visit if the code remains.
Read the related care guide.

Clothes still damp? Feel the air at the outside hood.
Clean the lint screen before every load, run the dryer for 5 to 10 minutes and hold your hand under the outside exhaust hood. No air means the vent is blocked, so clean the run or replace plastic or foil vent with metal. Kenmore guides call poor venting the most common dryer problem.

Dryer stopped at a power cut? Press and hold START, then check two breakers.
After a power cut, a Kenmore dryer may show PF: press and hold START to restart (press POWER first on some models). If the drum turns but there is no heat, check that both household breakers or fuses are on; an electric dryer uses two. L2 points to the home power supply.
When observation becomes a service request.
Leave internal testing to a technician.
The drum still will not turn with power, a latched door and START held. The guides do not give any further owner steps. Book a visit and mention any code, including F1, F2 or F20, which the 110 guide calls service codes.
Arrange a diagnosticSources and model boundaries.
These sources back up the Kenmore dryer drum not turning guidance. Read the manual that fits your model.
- Use & Care Guide, Kenmore Elite HE dryer 110.8772
- Use & Care Guide, Kenmore dryers 796.8128/9128/8118/9118
Go by the instructions for your exact model. Check how we research these pages.
Why won't my Kenmore dryer start or turn?
Power, the door latch and the START press come first. Electric models need both house fuses or breakers working.
Does the guide mention a belt?
The Kenmore dryer guides we read do not. We will not name a belt as the cause without a source.
What does PF mean on a dryer?
A power failure interrupted the cycle. Press and hold START to resume.
What are F1, F2 and F20?
The Elite HE 110 guide calls them service codes and gives no owner steps. Book a visit.
Code, symptom, part or service
Link the message to what comes next.
PF
PF means power failure: the dryer asks whether its drying cycle was interrupted when power dropped. On the 110 Kenmore dryers, press and hold START to restart. The 8756-series guide adds that you press POWER first.
Kenmore dryer takes too long
Long drying on a Kenmore dryer usually traces back to airflow: a clogged lint screen, a crushed or lint-packed exhaust vent, or a vent run that is too long. The guides give a quick test with your hand under the outside hood.
Dryer repair
Book a diagnostic for your model, carried out at the appliance.
Find your metro
Office details, and the access information to pass along.