Using your appliance

Sensor dry vs timed dry: choosing a cycle on a Kenmore dryer

Auto Dry cycles use a moisture sensor to decide when to stop, and the time on the display is an estimate. Timed Dry runs the minutes you set. Use Auto for normal mixed loads, Timed Dry for very small loads, and Damp Dry or the Damp Dry signal to catch items before they overdry.

Hand pulling a gray shirt from the open door of a dryer while heavier towels wait inside the drum.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Auto Dry senses moisture and shows an estimated time. Timed Dry shows actual time. 1
  • Dry Level works on Auto cycles only; temperature is set on Timed Dry. 12
  • A very small load may end an Auto cycle early; use Timed Dry or add wet items. 1
  • Light items mixed with heavy ones can fool the sensor. 1
  • The Damp Dry signal chimes just before the load is fully dry; the 796 steam dryer starts it by holding Wrinkle Guard. 123

What is the difference between Auto Dry and Timed Dry on a Kenmore dryer?#

Auto Dry uses a sensor that detects moisture in the clothes and adjusts the time, so the display shows an estimate that can change. Timed Dry runs the time you pick, and the display shows the actual time remaining. 12

The 796 guide describes Auto Dry cycles as using a sensor that detects moisture levels and adjusts the drying time as needed, with the dry level and temperature set for each cycle. Timed Dry lets you choose a specific amount of time and the drying temperature. 1

On the Elite HE the system is called Auto Moisture Sensing Plus. A thermistor, an electronic temperature sensor, and moisture sensing strips in the drum help measure how much moisture is in the clothes as they tumble. 2

How the time estimate behaves#

After the first 5 minutes of an Elite HE auto cycle, the estimated time adjusts for the approximate load size, cycle, dryness level and moisture left. When the clothes reach about 80% of the dryness level selected, it adjusts again and shows the final drying time. 2

So a time that moves around is not a failure. It is the sensor working. 12

Auto DryTimed Dry
How it stopsWhen the sensor decides the load is dry 12When the time you set runs out 1
DisplayEstimated time remaining 1Actual time remaining 1
Dry levelAdjustable 12Not available 12
TemperatureSet by the cycle 1Adjustable on the 796 1
TimeCannot be changed on the Elite HE 2More Time or Less Time 12

When should I choose Timed Dry instead?#

For a very small load, a single bulky item, or a load the sensor keeps misjudging. The 796 guide says a very small load on an Auto cycle gives the control too little to sense and it may shut off too soon. Use Timed Dry or add some extra wet clothes. 1

The 796 Timed Dry defaults are 40 minutes for Timed Dry, 25 for Express Dry and 20 for Touch Up, and the maximum for each is 100 minutes. Time moves in 1-minute steps with More Time and Less Time, or faster if you hold the button. 1

The rack and sensor strips#

On the Elite HE, do not use the dryer rack with an Auto cycle. The rack is for Rack Dry or Air cycles. If an automatic cycle ends early, the load may not be touching the sensor strips, so level the dryer, or raise the dryness level setting. 2

  1. 1

    Sort by weight#

    Separate heavy items from lightweight ones. Larger and heavier items take longer, and light items in a heavy load can fool the sensor because they dry faster. 1

  2. 2

    Pick the cycle#

    Auto Dry for a normal load of similar items. Timed Dry for a very small load or when you want exact minutes. 1

  3. 3

    Set the dry level#

    On Auto cycles, press Dry Level or Dryness Level for More Dry, Normal or Less Dry. Normal uses the least energy on the Elite HE. 12

  4. 4

    Start the cycle#

    The Elite HE needs START held about 3 seconds; the 796 uses the START/PAUSE button. 12

  5. 5

    Finish by hand if needed#

    If a few items are still damp, a short Timed Dry is a simple way to finish them. That is our suggestion, not a line from the guide.

If every Auto load comes out damp#

The Elite HE lets you raise the preset dryness level for all Auto cycles. With the dryer stopped, hold Dryness Level for 5 seconds until it beeps and shows CF, then press the button to pick setting 1, 2 (about 15% more time) or 3 (about 30% more) and press START to save. 2

What does the Damp Dry signal do?#

It chimes just before the load is fully dry, so you can pull items to iron or hang up. On the Elite HE it signals at about 80% dry and works on Auto cycles only. On the 796 it chimes when clothes are just short of completely dry. 12

On the Elite HE, when the signal sounds, open the door, rearrange the load, close it and restart to finish. That helps sheets and bulky items dry more evenly. For the Bulky/Bedding cycle the signal is preset ON. 2

How you turn it on#

The button for the signal is not the same on every family, so match your panel to the list below. 123

  • 796.8128 family: press the Damp Dry Signal option button. 1
  • Elite HE 110.8772: select Damp Dry Signal in the options. 2
  • 796.8138 steam family: press and hold the Wrinkle Guard button for about three seconds. 3

Check which buttons your panel has. The names change with the model.

Damp Dry as a dry level#

On the 796 guide, the Dry Level setting has Damp Dry on the low end and Extra Dry on the high end. Use Damp Dry for items you will iron or hang for final drying. Extra Dry increases the cycle time. 1

A worn rating label on the rim of an older top-load washer
Your model number tells you which family's buttons apply.

Why do clothes come out static, wrinkled or damp?#

The guides give short answers. Overdrying causes static and wrinkles: use a shorter time, the Damp Dry setting, or an Auto cycle. Damp clothes point to the load, the dry level, the lint screen or the vent. 1

  • Static. Overdrying builds static. Synthetics and permanent press are more prone to it. Try fabric softener, Damp Dry or a shorter Timed Dry. 1
  • Wrinkles. Remove items while they still hold a slight amount of moisture. The Wrinkle Guard option tumbles briefly every few minutes after the cycle for up to 150 minutes on the 796.8128, or 180 on the 796.8138. 13
  • Long drying. The cause may be airflow, not the cycle. Clean the lint screen and see our airflow guide. 1
  • Inconsistent times. The guide says drying time varies with heat type, load size, fabrics, wetness and the condition of the duct and lint filter. A badly spun load from the washer makes the next load slower. 1

When should I book a technician?#

Book a visit if Auto cycles keep ending early or running very long on a normal, sorted load after the lint screen and the vent are clean, or if a code stays on the display. tE1 or tE2 on a 796 dryer is a temperature sensor failure: turn the dryer off. 13

Tell us which cycle you use, the size of the load and what the clothes feel like at the end.

You can book a visit, read about our dryer service or see the dryer takes too long page. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. If your unit is under the manufacturer's warranty, the manufacturer handles that repair. We give a warranty on our workmanship.

Sources#

  1. Use & Care Guide, Kenmore dryers 796.8128/9128/8118/9118Kenmore / Sears Brands · Document 1901122L (part MFL67731010), no date printed · pp. 19-21 (Operating the Dryer, Cycle Guide), 24-25 (Cycle Modifier Buttons, Damp Dry Signal), 29-31 (Troubleshooting)
  2. Use & Care Guide, Kenmore Elite HE electric dryer 110.8772Kenmore / Sears Roebuck · Document L0708325 (part W10136973A), no date printed · pp. 20-21 (Dryer Use, Auto Moisture Sensing Plus), 24-25 (Options, Damp Dry Signal, Dryness Level), 28-29 (Troubleshooting)
  3. Use & Care Guide, Kenmore steam dryers 796.8138/9138Kenmore / Sears Brands · Document 1405214L (part MFL67731025), no date printed · p. 25 (Wrinkle Guard, Damp Dry Signal)

Here to help

Good questions.
Clear answers.

Talk to our team
What is the difference between Auto Dry and Timed Dry?

Auto Dry uses a sensor that detects moisture and adjusts the time, so the display shows an estimate. Timed Dry runs the time you set, and the display shows actual time remaining. See source 1, pages 20 and 21.

Why does my dryer stop before the clothes are dry?

On an Auto cycle the sensor may be fooled by a very small load or by light items mixed with heavy ones. The guide says to use Timed Dry, add a few wet items or sort by weight. See source 1, page 30.

What does the Damp Dry signal do?

It sounds a chime when clothes are about 80% dry on the Elite HE, or just short of dry on the 796, so you can pull items for ironing or hang drying. On Elite HE dryers it works on Auto cycles only. See source 2, page 24.

Can I change how dry Auto Dry gets the clothes?

Yes, with the Dry Level or Dryness Level button: More Dry, Normal or Less Dry. It works only on Auto cycles, not Timed ones. Normal is the setting the Elite HE guide says uses the least energy. See sources 1 and 2.

Why is a small load a problem for an Auto cycle?

With a very small load the control cannot sense the dryness properly and may shut off too soon. The 796 guide says to use Timed Dry or add some extra wet clothes. See source 1, page 30.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.