On this page
- The guides say never to store the washer where it can freeze; water lines and internal parts can be damaged. 12
- Antifreeze amounts differ by family: 1 gallon on the 796, 1 quart on the Calypso and 110 front-load. 1234
- Run a cycle after storage to clear the antifreeze, with no laundry. 1234
- A 796 washer that has been frozen should warm up before you press POWER. 2
- A 110 front-loader's transport bolts are a service step, and the washer travels upright. 4
Can a Kenmore washer sit in a cold garage over the winter?#
Not safely, if the garage can freeze. Every Kenmore washer guide here says to install and store the washer where it will not freeze, because water left in the hoses and pump can freeze and damage them. 13
The 796 front-load guide says the washer should never be installed or stored where it can freeze, and that damage can reach the water lines and the internal mechanisms. It adds that rust or other damage from storage in the weather or in freezing temperatures may not be covered by the product warranty. 1
If the washer has to wait out the winter in a cold place, or you are moving it in cold weather, each guide gives a routine, which this guide pulls together. The steps and the amounts differ by family, so find yours first.
What does each family say to do?#
All four guides follow the same shape: water off, hoses drained, antifreeze in the drum, a short spin, power off. The amount of antifreeze and the spin are different, so use the row for your washer. 1234
| Family | Antifreeze | Spin to run | Clearing it afterward |
|---|---|---|---|
| 796 front-load | 1 gallon of nontoxic RV antifreeze in the empty drum 1 | Press POWER, then SPIN SPEED with no cycle chosen, then START/PAUSE to run the drain pump 1 | Run the EXPRESS cycle, no laundry 1 |
| 796 top-load | 1 gallon of nontoxic RV antifreeze in the empty tub 2 | Select spin and let it spin for 1 minute 2 | Run a complete cycle with detergent, no laundry 2 |
| 110 Calypso top-load | 1 quart (1 L) of RV-type antifreeze in the basket 3 | Extended Spin for about 30 seconds 3 | Run with the recommended amount of HE detergent 3 |
| 110 front-load | 1 quart (1 L) of RV-type antifreeze in the drum 4 | A Drain & Spin cycle 4 | Normal/Casual cycle with half the usual HE detergent for a medium load 4 |
Pick the row for your family and ignore the others. Do not carry one family's antifreeze amount over to another.
How do I winterize a 796 front-load washer?#
Turn the water off, unhook and drain the hoses, plug the washer in, add 1 gallon of nontoxic RV antifreeze to the empty drum, run the drain pump with POWER and SPIN SPEED, then unplug it, dry the drum and store it upright. 1
- 1
- 2
- 3
- 4
- 5
- 6

When you bring the washer back, run the EXPRESS cycle with no laundry to clear the antifreeze. 1
How do I winterize a top-load washer?#
The 796 top-load and the Calypso each have their own version. The 796 uses 1 gallon of antifreeze and a 1-minute spin. The Calypso uses 1 quart and about 30 seconds on Extended Spin. Both end with the washer unplugged. 23
On a 796 top-load#
Shut off the tap and drain the hoses, plug the washer in, add 1 gallon of nontoxic RV antifreeze to the empty tub and close the lid. Select spin and let it run for 1 minute. The guide says not all of the antifreeze is expelled. 2
Then unplug it, dry the tub with a soft cloth, close the lid, remove the dispenser inserts and dry the compartments, and store it upright. After storage, run a complete cycle with detergent and no laundry. 2
On a Calypso#
Shut off both faucets, disconnect and drain the inlet hoses, put 1 quart (1 L) of RV-type antifreeze in the basket, run Extended Spin for about 30 seconds to mix it with the remaining water, then unplug the washer. 3
To use it again: flush the water pipes and hoses, reconnect the hoses, turn on both faucets, plug the washer in and run it with the recommended amount of HE detergent to clean out the antifreeze. 3

How do I move a Kenmore washer in freezing weather?#
Prepare it the same way as for storage, then secure the hoses and cord. The Calypso and 110 front-load guides add transport steps, and the 110 front-load guide says to call for service for the transport bolts. 34
On a Calypso: shut off both faucets, drain the hoses, put the quart of antifreeze in the basket if the move is in freezing weather, run Extended Spin for about 30 seconds, disconnect the drain, unplug it, put the hoses in the basket and drape the cord and drain hose over the edge. Then place the foam plug from the original shipping material into the basket opening, close the lid and tape it to the front. 3
On a 110 front-loader: put the quart of antifreeze in the drum, run Drain & Spin, unplug, move the drain hose to the clips on the rear panel, shut off both faucets, and drain the inlet hoses and clip them to the rear panel. The guide says transport bolts must not be reused, that the washer must travel upright, and that a technician should set it up for relocation. 4
If you would rather not handle that step, give us the model number ahead of the move and we will plan it with you. You can request a visit here.
Why won't the washer fill or drain after being cold?#
Start with frozen hoses. The 110 front-load guide lists frozen inlet hoses under its water inlet message and a frozen drain hose under its drain message. Thaw the hose, then try again. 4
The guide has you cancel the cycle, disconnect power and then look at the faucets, the screens at the inlet hose connection, kinked hoses and frozen hoses. It does the same for drain: kinked, frozen or clogged hose, or a drain more than 96 inches (2.4 m) above the floor. 4
Those messages are explained on the F20 entry and the Ld, F21 and F02 page.

What if the display will not come on?#
On the 796 top-load, the guide says a washer exposed to temperatures below freezing for an extended time should warm up before you press POWER, or the display will not come on. 2
The 796 front-load guide gives a matching instruction for a washer that froze before installation: leave it at room temperature for several hours and check for leaks before you run it. 1
What should I do the first time I run it after the cold?#
Warm the washer, reconnect and flush the hoses, check the connections for leaks and run the cleaning cycle your guide names for the antifreeze. Then wash a small load and watch for leaks on the first fill. 1234
The 796 guides say to flush a gallon or two of water through each inlet hose before connecting, which also helps remove debris that could clog the screens. 12 If the screens do clog, the inlet screen entry shows where they are.
The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. The washer service page lists what we repair.

Sources#
- Use & Care Guide, Kenmore front-load washers 796.4136/4146/4156Kenmore / Transform SR Brands · Document 1909134L (part MFL68005592), no date printed · pp. 7 (installation warning), 9 (Water Supply), 41 (Storing the Washer)
- Use & Care Guide, Kenmore top-load washer 796.2927Kenmore / Sears Brands · Document 1007244L (part MFL42065471), no date printed · pp. 9 (Water Supply), 24 (Storing the Washer), 29 (Washer is too cold)
- Use & Care Guide, Kenmore Calypso top-load washers 110.2206Kenmore / Sears Roebuck · Document L0412465 (part 8543703), no date printed · p. 17 (Non-use or vacation care, winterizing, transporting)
- Use & Care Guide, Kenmore front-load washers 110.4708/4709Kenmore / Sears Roebuck · Document L0809415 (part 8183014B), no date printed · pp. 21-22 (Non-use care, winterizing, transporting, F20 and F21)


