Using your appliance

Filling the steam feeder on a Kenmore 796 dryer: water, ADD WATER and steam cycles

Pull out the drawer, lift out the steam feeder, fill it with cool tap water to the MAX line and seat it back until the drawer clicks shut. Never use hot or distilled water. If the ADD WATER light blinks, the cycle cancels: refill the feeder and restart.

Hands pouring water from a plastic jug into a clear removable tank held above a pulled-out drawer on the top front of a dryer.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Fill with ordinary tap water to the MAX line; no hotter than 86°F. 1
  • No distilled water: the water level sensor will not work. 1
  • ADD WATER blinking cancels the cycle; refill and restart. 1
  • Steam is invisible and the drum turns only a few seconds a minute. 1
  • Empty the feeder before moving the dryer. 1

How do I fill the steam feeder on a Kenmore steam dryer?#

Pull out the drawer, lift out the steam feeder, fill it with ordinary tap water to the MAX line, set it back in the drawer and push the drawer in until it clicks. Do this before every steam cycle. 1

This guide covers the Kenmore steam dryers 796.8138 and 796.9138. The guide says the water must reach the MAX line or touch the filter screen, and that the drawer has to be completely closed. 1

  1. 1

    Pull out the drawer#

    The steam feeder sits in a drawer on the dryer. Pull the drawer out. 1

  2. 2

    Lift out the feeder#

    Take the steam feeder out of the drawer so you can fill it. 1

  3. 3

    Fill it with cool tap water#

    Use ordinary tap water up to the MAX line or until the water touches the filter screen. The water must be no hotter than 86°F (30°C). 1

  4. 4

    Set it back and close the drawer#

    Place the feeder in the drawer, then push in the drawer until it latches. 1

  5. 5

    Wipe up spills#

    Wipe any water spilled around the feeder and the drawer before you start the dryer. 1

What water is allowed#

Only water. The guide says not to fill the feeder with other liquids, rinse agents or detergents, and not to use distilled water, because the water level sensor in the steam generator will not work with it. 1

It also warns against hot water over 86°F (30°C), because of a burn hazard. Do not drink water from the steam feeder, and never put gasoline, dry-cleaning solvents or other flammable substances in it, because the vapors can explode. 1

Moving the dryer#

Water left in the feeder can spill during a move. Before you move the dryer, make sure the steam feeder is empty. 1

What does the ADD WATER light mean?#

The steam feeder is running low. The guide says the ADD WATER light will blink and the cycle will cancel. Turn the dryer off, refill the feeder to the MAX line and restart the steam cycle. 1

It can also happen the first time you use steam, because the feeder may not have enough water yet. Fill it and start again. If the feeder is not filled to the MAX line, the light may come on early. 1

If steam seems not to work#

Most steam problems are the feeder, not the dryer, and the guide says so. Check these in order, which is the guide's own list for "steam features not working": 1

  1. 1

    Look for condensation#

    Steam is not directly visible. Condensation on the door glass during the steam portion of the cycle is normal. 1

  2. 2

    Check the water level#

    Make sure the steam feeder is filled with water to the MAX line. 1

  3. 3

    Check the seating#

    Make sure the feeder is seated properly and the drawer is fully closed. 1

  4. 4

    Turn the dryer off and on#

    Then restart the steam cycle. 1

  5. 5

    Check the water type#

    Do not use distilled water. If everything above is right, the guide says a steam feeder pump that is not working is a service call. 1

How do the steam cycles work?#

During steam, the drum barely moves: it turns only a few seconds, once a minute, so the steam vapor stays in the drum. The steam is released at different stages of the cycle, and you cannot see it. 1

Steam Refresh is for reducing wrinkles and odors. It takes one to five garments or one bulky item such as a comforter, with three settings: one to three garments, four or five garments, and a big setting for bulky items. 1

Which fabrics#

The guide says not to use Steam Refresh on wool, wool blankets, leather jackets, silk, wet clothes, lingerie, foam products or electric blankets. For good results load articles of similar size and fabric type, and do not overload. 1

It works most effectively on 70/30 cotton and polyester blends, and not on 100% cotton items. If clothes are still wrinkled at the end, load only one to five garments or one bulky item and do not mix fabric types. 1

Static Shield and Iron Ready#

Static Shield uses steam to reduce static electricity caused by dry fabrics rubbing together. Iron Ready leaves fabrics evenly damp for ironing: press and hold the Static Shield button for three seconds to reach it. The guide uses the More Time and Less Time buttons to set the number of articles. 1

When Static Shield is added to an auto dry cycle, the Damp Dry level cannot be selected. Fabric softener sheets are not recommended with steam cycles. 12

A worn rating label on the rim of an older top-load washer
The model number shows whether you have a 796 steam dryer.

Is a steam dryer different from the Elite HE SteamCare cycles?#

Yes. The 796.8138 has a drawer with a steam feeder you fill by hand. The Elite HE 110.8772 SteamCare cycles instead need a water inlet hose connected to a cold water faucet and the dryer's inlet valve, with the supply turned on. 12

On the Elite HE, if clothes are still wrinkled after a SteamCare cycle, the guide says to check the hose at both ends and that the water is on. It also advises against fabric softener sheets in SteamCare cycles. 2

What other things are normal?#

Water dripping down the door glass during steam is condensation from the invisible steam. The guide lists a few more normal things: no visible steam at the start of the cycle, and odors that are very strong not fully leaving. Strong odors should be washed or dry cleaned instead. 1

Safety during steam#

Do not open the dryer door during a steam cycle, because steam can cause severe burns. Do not touch the steam nozzle in the drum during or after a cycle. 1

Should I book a technician for steam problems?#

Book a visit if steam still does not work after the feeder is filled to MAX with tap water, seated, the drawer is closed and the dryer has been turned off and on. The guide treats a feeder pump that is not working as a service call. If tE1 or tE2 shows, turn the dryer off and call. 1

Tell us the model number, what the ADD WATER light does and what kind of water you used. If you used distilled water, say so, and switch to ordinary tap water before the visit, since the guide says the water level sensor in the steam generator will not work with distilled water. 1

You can book a visit, read about our dryer service or see the dryer temperature problems page. The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. If your unit is under the manufacturer's warranty, the manufacturer handles that repair. We give a warranty on our workmanship.

Sources#

  1. Use & Care Guide, Kenmore steam dryers 796.8138/9138Kenmore / Sears Brands · Document 1405214L (part MFL67731025), no date printed · pp. 6 (Safety Instructions for Steam Functions), 23 (Time and Status Display), 26-27 (Steam Features, Filling the Steam Feeder), 31-33 (Before Calling for Service)
  2. Use & Care Guide, Kenmore Elite HE electric dryer 110.8772Kenmore / Sears Roebuck · Document L0708325 (part W10136973A), no date printed · pp. 21 (SteamCare cycles), 29 (Troubleshooting: steam)

Here to help

Good questions.
Clear answers.

Talk to our team
What water goes in a Kenmore steam dryer?

Ordinary tap water, filled to the MAX line, and never hot: the guide says not to fill the feeder with water over 86°F (30°C). Do not use distilled water, rinse agents or detergents. See source 1, pages 6 and 27.

Why is the ADD WATER light blinking?

The steam feeder has run low. The guide says the light blinks and the cycle cancels. Refill the feeder to the MAX line and restart the cycle. It can also happen the first time steam is used. See source 1, pages 23 and 27.

Why can I not see any steam?

The guide says steam is not clearly visible during steam functions, and that this is normal. You may see condensation on the door glass instead. See source 1, pages 26 and 33.

Why does the drum barely turn during a steam cycle?

It is meant to. The drum is turned off so the steam stays in it, and it turns only for a few seconds, once a minute. See source 1, page 33.

Can I open the door during a steam cycle?

No. The guide warns that steam can cause severe burns. Do not touch the steam nozzle in the drum during or after a cycle either. See source 1, pages 6 and 26.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.