Maintenance

Kenmore gas burners after a spill: caps, ports and the flame

After a spill, let the burners cool, lift off the caps, clear the slots with a soft brush and the small ignition port with a paper clip end, dry everything, and seat each cap so it sits level and centered. A steady, mostly blue flame means the burner is clean and the cap is right. Smell gas, and you stop and follow the safety steps.

Gas cooktop with one burner cap removed, showing a grimy burner head; the cap, a toothbrush and a paper clip rest on a towel nearby.
Experienced techniciansWarranty on our workmanshipOEM parts available on orderUpfront pricing, agreed before work
On this page
Key points
  • Clean only when every burner is off and cool. 12
  • Burner heads are cleaned in place; the caps come off, and caps do not go in the dishwasher. 12
  • A partly blocked ignition port can cause ignition problems; clear it with a small wire or paper clip end. 12
  • A good flame is clear, blue, steady and hardly visible in a well-lit room. 1
  • A cap not seated correctly can mean an improper flame size and uneven heating. 12

Why will my Kenmore gas burner not light or burn evenly after a spill?#

A spill that runs into the burner slots or the small ignition port is the usual reason. The guides say a partly blocked port can cause ignition problems and that clogged ports give a flame that burns only part way around. 123

The cure in the guides is cleaning, not repair: lift the cap, brush the slots, clear the port, dry everything and seat the cap. This guide follows their order. It does not diagnose igniters; if cleaning does not help, that is a visit.

What do I clean, and in what order?#

Work from the outside in: grates, caps, then the heads and ports, always on a cool cooktop. Switch all burners off and give them time to cool before you start; the guides warn about burns. 12

PartWhat the guide saysSource
GratesClean when cool with a nonabrasive plastic pad and mild abrasive cleanser; dry at once. On the 790.7540 they are dishwasher safe 121 p. 36, 2 p. 25
Burner capsRemove after cooling, clean heavy soil with a plastic pad and cloth, dry the bottom and inside, no abrasives, not in the dishwasher 121 p. 36, 2 p. 25
Burner heads and slotsSecured to the cooktop, cleaned in place; soak up spills with a damp cloth, brush food from the slots with a soft nonabrasive brush such as a toothbrush 121 p. 37, 2 p. 25
Ignition portA small port on each head; clear it with a fine needle or the end of a paper clip, head in place 121 p. 37, 2 p. 25
Gas burner head with slots and a small round port, its dark cap set beside it and a toothbrush nearby on a counter.
The cap lifts off. The head stays on the cooktop and is cleaned in place. 12

The bridge burner on some ranges is the exception: the 790.7540 guide says it is removable and points to its assembly section for the correct installation. 2

How do I clear the slots and the ignition port?#

Soak up the spill with a damp cloth, brush the food out of the slots with a toothbrush, then clear the ignition port with a thin wire, a needle or the end of a paper clip, with the head in place. Keep anything from falling into the gas port opening. 12

  1. 1

    Wait until the burners are cool#

    The guides say all surface burners must be off and cool before you begin. 12

  2. 2

    Lift off the cap#

    Set it aside to clean separately. The head underneath is secured to the cooktop. 12

  3. 3

    Soak up the spill#

    Use a clean damp cloth. 12

  4. 4

    Brush the slots#

    Remove food from between the burner slots with a small nonabrasive brush like a toothbrush, then wipe with a damp cloth. For stubborn soil, use a thin wire or a needle. 12

  5. 5

    Clear the ignition port#

    With the head in place, use a fine needle or the end of a paper clip to clear the port or ports. 12

  6. 6

    Mind the electrode#

    The Elite gas guide says any spill on or around the electrode must be carefully cleaned, and warns not to hit it with anything hard or it could be damaged. 1

Hand holding a straightened paper clip to the small ignition port of a gas burner head.
Clear the small ignition port with the head in place. 12

For gas to flow and ignite properly, no spill, crumb or cleaning product should get into the gas orifice opening. 12

How do I put the burner cap back correctly?#

Dry the cap, set it on the head so its lip sits snug in the center, and slide it gently side to side. It should rest level, give a click when the lip meets the center and not move off center. 1

The cap matters as much as the ports. The guides say the cooktop should not be used without all caps properly installed, to prevent flare-ups and to get the proper ignition and flame size. 1 A cap sitting wrong can give an improper flame size and uneven heating. 2

Gas burner with a round dark cap seated on its head and a ring of steady blue flame around the edge.
Level, centered and clicked into place. 12

Dry the cap first, including the bottom and the inside, as the guide requires, because moisture left behind is a listed cause of a flame that burns half way around. 13

What should the flame look like?#

Clear, blue and steady, faint to the eye in a bright room, with each cone sharp. If it is yellow-orange, the guide says the burner needs cleaning or adjusting. Never let the flame go past the outer edge of the pan. 1

What you seeCause in the guidesWhat to do
Flame burns half way aroundClogged ports, or moisture after cleaning 23With the burner off, clear the ports with a wire or needle; or, after drying the burners, fan the flame lightly and keep the burner on until the flame is full 23
Orange flameDust particles in the gas line, or salt air in coastal areas 23Let the burner run a few minutes until the flame turns blue; a slightly orange flame in coastal areas is unavoidable 23
Yellow-orange flame that staysA burner that needs cleaning or adjusting 1Work through the cleaning steps above 1

What if the burners will not light at all?#

Check the knob, the cord and the gas supply. The troubleshooting tables say the knob must be pushed in and turned completely to LITE until the burner ignites, then turned to the flame size you want. Also look at the cord, the house lights and the gas valve. 23

  1. 1

    Turn the knob fully to LITE#

    Push it in and turn it until the burner ignites, then turn it to the flame size you want. 23

  2. 2

    Check the cord#

    The 790.7540 guide lists a range disconnected from the outlet. 2

  3. 3

    Check for an outage#

    Look at the house lights. The guides say surface burners can be lit manually during an outage. 23

  4. 4

    Confirm the gas supply is on#

    Both guides list the gas supply being off. 23

  5. 5

    Clean the ports#

    The guides list clogged ports as a cause of burners that do not light. See the steps above. 23

The burner will not ignite page and the burner problems page carry the symptom view.

When should I book a visit?#

When cleaning, a dry burner and a seated cap do not fix it, or when you smell gas. A burner that still will not light, or lights unevenly, after those steps is beyond what the guides ask you to do yourself. 123

The technician agrees the price with you before any work starts. The exact cost is confirmed after the on-site diagnostic. The range service page lists what we repair.

Flashlight glow on a small blank rating label on the frame beside an open dryer door hinge, the drum visible at right.
The number before the dot tells us which guide applies.

Sources#

  1. Use & Care Guide, Kenmore Elite slide-in gas range 790.4260/4261Kenmore / Sears Brands · Document 1403611L (part 139901309 Rev. A) · pp. 3 (Important Safety Instructions), 9 and 12 (Burner Cap Placement, Flame Size), 36-37 (Care and Cleaning)
  2. Use & Care Guide, Kenmore range 790.7540Kenmore / Sears Brands · Document 1608081L (part 318200773 Rev. A) · pp. 25 (General Care and Cleaning), 28 (Before You Call)
  3. Use & Care Guide, Kenmore Elite dual-fuel slide-in range 790.4103/4104Kenmore / Sears Brands · Document L0810108 (part 318203893 Rev. A) · p. 46 (Before You Call)

Here to help

Good questions.
Clear answers.

Talk to our team
Why does my burner flame burn only half way around?

The guides give two causes: clogged burner ports, which you clear with a thin needle or wire while the burner is off, and moisture left after cleaning, which you burn off by letting the burner run until the flame is full. See source 2, page 28.

Is an orange flame dangerous?

The guides say dust in the gas line can turn it orange and that it should turn blue after a few minutes. They also say a slightly orange flame is unavoidable in coastal areas with salt air. A flame that stays yellow-orange needs the burner cleaned. See source 1, page 12, and source 2, page 28.

Can I put the burner caps in the dishwasher?

No. The guides say not to clean burner caps in the dishwasher or with abrasive cleaners. Wash them by hand and dry them well, including the bottom and the inside. See source 1, page 36.

What should I do if the burners will not light at all?

Check that the knob was pushed in and turned all the way to LITE, that the cord is plugged in and the gas supply is on, and clean the ports. During a power outage the guides say surface burners can be lit manually. See source 2, page 28.

Can I use a toothpick or a metal pin on the ports?

The guides name a toothbrush for food between slots, and a thin wire, a needle or the end of a paper clip for stubborn soil and the ignition port. They do not mention toothpicks. See source 1, page 37, and source 2, page 25.

Let’s take care of it.

Still going after all these years.
Let’s keep it that way.